Dual TB9051FTG Motor Driver - dual DC motor driver for Arduino
ID: 572195
5906623478736
zł122.25
Tax included
zł99.39 tax excl.
Dual DC motor controller designed for Arduino, which enables the motor to be supplied with voltage in the 4.5 ... 28V range and power consumption in continuous operation of 2.6 A (5A at the top) of two DC motors. Polol 2520
Description
Universal dual DC motor controller designed for Arduino . The controller can be used for motors supplied with voltage in the 4.5 ... 28 V range and for power consumption in continuous operation of 2.6 A (5 A in peak) of two DC motors. The controller is protected by overheating and overcurrent and has reverse voltage protection. The motors are controlled using a PWM signal with a frequency up to 20 kHz.
properties
- Two single H-bridges (TB9051FTG chip)
- Supply voltage for motors: 4.5 ... 28 V
- Maximum power consumption: 2.6 A (5 A at peak)
- PWM signal frequency up to 20 kHz
- Protection against overheating and system overload
- Reverse protection circuit
- The automatic step-stop mode prevents the system from overheating during sudden braking
- It is possible to use D24V5F9 or S10V3F9 inverters as the power source
- Dimensions: 48 x 51 x 7.6 mm
- Weight: 11 g
Included
- Dual TB9051FTG Motor Driver Shield for Arduino extension
- 1 x extended 10-pin female connector
- 2 x 8-pin female extension connector
- 2 x extended female connector 6-pin
- 3 x 2-pin screw connector
- 25-pin male connector
- jumper
572195
Data sheet
- Output current
- 2,6 V
- Number of channels
- 2
- Supply voltage min
- 4,5 V
- Supply voltages max
- 28 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
TB9051FTG Single Brushed The DC Motor Driver Carrier is a single DC motor driver that allows the motor to be supplied with voltage in the 4.5 ... 28V range and power consumption at a continuous 2.6 A (5A peak) operation. Pololu 2997
zł47.04
24h
Available quantity: 1
Available
Dual DC motor controller designed for Raspberry Pi, which enables the engine to be supplied with voltage in the 4.5-28V range and power consumption in continuous operation of 2.6A (5A in peak) of two DC motors. Pololu 2762
zł155.91
24h
Available quantity: 1
Available
Dual DC motor controller designed for Raspberry Pi, which enables the engine to be supplied with voltage in the 4.5-28V range and power consumption in continuous operation of 2.6A (5A in peak) of two DC motors. Self-assembly set. Pololu 2761
zł134.54
24h
Available quantity: 1
Available
Other products in the same category (16)
Motor-driven expansion board for Arduino, L293D, 74HC595 shift register, RoHS
zł9.45
24h
Available quantity: 6
Available
(DRI0009) 2A Motor Shield For Arduino
zł61.27
24h
Available quantity: 2
Available
No product available!
This Kit with fully-dedicated PWM driver chip handles all the motor and speed controls over I2C. Only two data pins (SDA & SCL in addition to the power pins GND & 5V) are required to drive the multiple motors; you can also connect any other I2C devices or shields to the same pins. This makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3. Adafruit 1438
zł102.94
24h
Available quantity: 3
Available
This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its dual robust VNH5019 motor drivers operate from 5.5 to 24 V and can deliver a continuous 12 A (30 A peak) per motor, or a continuous 24 A (60 A peak) to a single motor connected to both channels. Pololu 2507
zł294.77
4 weeks
No product available!
Pololu - 2511
zł41.29
24h
Available quantity: 1
Available
Pololu 2512Module with 2-channel DC motor driver for Arduino boards. It allows you to control drives with a supply voltage from 6 to 32 V and a current consumption of up to 0.65 A. Pololu 2512
zł66.92
24h
Available quantity: 3
Available
Two axis stepper motor driver expansion board based on the L6470 for STM32 Nucleo
zł78.49
24h
Available quantity: 1
Available
Quad DC Motor Driver Shield is an Arduino compatible DC motor driver that allows you to control 4 DC motors with a voltage between 2.5 ... 13.5V and up to 1.2A. DFRobot DRI0039
zł63.31
24h
Available quantity: 2
Available
Available
zł374.87
24h
Available quantity: 1
Available
This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 V operating range and are efficient enough to deliver a continuous 18 A without a heat sink.
zł288.26
24h
Available quantity: 1
Available
Pololu Dual G2 High-Power Motor Driver 24v18 is an extension that allows you to control two DC motors designed for Arduino tiles. The motor can be supplied with 6.5 ... 40V voltage and can draw a maximum current of 18A. Pololu 2518
zł420.17
4 weeks
No product available!
Pololu Dual G2 High-Power Motor Driver 18v22 is an extension that allows you to control two DC motors designed for Arduino tiles. The motor can be supplied with 6.5 ... 30V voltage and can draw up a maximum current of 22A. Polol 2517
zł598.99
4 weeks
No product available!
DRV8825 Stepper Motor Driver Module for Arduino. It allows you to control two drives, equipped with an XBee connector. DFRobot DRI0023
zł159.16
24h
Available quantity: 1
Available
Gravity: IO Expansion & Motor Driver Shield is an Arduino compatible expansion board that provides digital I / O ports, analog I2C, SPI and UART interfaces, as well as a DC motor driver. DFRobot DFR0502
zł65.65
24h
Available quantity: 3
Available
Dual DC motor controller designed for Arduino, which enables the motor to be supplied with voltage in the 4.5 ... 28V range and power consumption in continuous operation of 2.6 A (5A at the top) of two DC motors. Polol 2520