New products
New products New products
Best sellers
There are 16652 products.
This is the FeatherWing OLED: it adds a 128x32 monochrome OLED plus 3 user buttons to any Feather main board. Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top of your Feather board and let the board take flight. Adafruit 2900
Module with a temperature and humidity sensor based on the SHT31-D system. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 2857
Module with a GPS receiver based on the MTK3333 system. Dedicated to Feather plates, communicates via the UART interface. Adafruit 3133
Tiny (18 x 44 mm) breadboard-friendly development board, easy to use, hacker friendly. ATmega328 brains32KB of flash (1/2 K is reserved for the bootloader), 2KB of RAM, clocked at 16MHz. Adafruit 2590
Expander (shield) compatible with Arduino and NUCLEO (STM32) systems, equipped with a Bluetooth 4.1 (BLE) radio module from the SPBTLE-RF family
OS Preinstalled Flash Memory with Android
OS Preinstalled Flash Memory with Android
Prototype board designed to cooperate with Particle Photon. The board has prototype holes with a 2.54 mm pitch and pins of the I2C interface. SparkFun DEV-13598
Particle’s IoT (Internet of Things) hardware development kit, the Photon, provides everything you need to build a connected project. Particle has combined a powerful 120Mhz ARM Cortex M3 micro-controller with a Broadcom Wi-Fi chip in a tiny thumbnail-sized module called the PØ (P-Zero)
This level shifter board contains 3 x TSX0108E bi-directional level shifter ICs. The 30-pin and 12-pin GPIO ports on the XU4 are converted to the more common 0.1inch (2.54mm) pitch 40-pin header. All the signals can be level shifted to 3.3V or 5V.
The driver with the TPIC6C596 system allows you to control 7-segment displays using three signal lines. Serial connection of controllers is possible. SparkFun WIG-13279
D-SUB signal socket (female, angled). It has 15 pins in the system of 3 rows of 5 pins (VGA), the line spacing is 1.98mm. The socket is blue, mounted for printing
This is a simple to use motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. This unit works great from 5 to 12V (datasheet shows 12V). You can also install a jumper wire past the 5V regulator on board to make this unit work at 3.3V. Sensor uses 1.6mA@3.3V. SEN-13285
This disc load cell (sometimes called a strain gauge) can translate up to a whopping 200kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the disc. SEN-13332
This compact board breaks out the pins of a microSD card connector necessary to interface with the card through SPI (Serial Peripheral Interface), and it can be directly integrated into 5 V systems thanks to its on board 3.3 V regulator and level shifting circuity. Pololu 2587
X-NUCLEO-IDS01A4 is a development board STM32 Nucleo that allows the use of the RF SPSGRF-868 module for the ISM band (868 MHz carrier).
32-bit microcontroller from the STM32F7 family with ARM Cortex-M7 core, 512kB Flash memory, 320kB SRAM, I2C, SPI, UART / USART memory, USB, CAN, 1.7 ... 3.6V, 144LQFP, STM, RoHS