Best sellers

Two-channel touch light switch with WiFi, which can control two lighting circuits in the room. It allows you to independently turn on/off each of the two channels and set time schedules using the EWeLink application. Sonoff T0EU2C TX

Evaluation kit equipped with STM32F401CCU6 microcontroller (ARM Cortex M4, 84MHz, 256kB Flash, 64kB RAM). It has two 20-pin connectors enabling the use of numerous microcontroller peripheral systems.

Evaluation kit equipped with STM32F103C8T6 microcontroller (ARM Cortex M3, 72MHz, 64kB Flash, 20kB SRAM). It has two 20-pin connectors enabling the use of numerous microcontroller peripheral systems.

A compact and cost-effective digital oscilloscope with four channels, 70 MHz bandwidth, and 12-bit resolution, ideal for professional and educational applications. It offers a sampling rate of up to 1.25 GSa/s, 25 Mpts of memory, and an acquisition rate of up to 1,000,000 wfms/s in UltraAcquire mode, enabling precise capture of even rare signal anomalies. Equipped with a 7-inch touchscreen, intuitive controls, USB, LAN, and HDMI interfaces, and USB-C power, it offers ease of use and portability.

RS422 to TTL converter module based on MAX490 for long-distance bidirectional serial communication, up to 1000 meters, with a transmission speed of up to 2.5 Mbps. Equipped with ESD protection up to 15 kV, TVS diodes and 120 Ω terminating resistors, it provides stability and immunity to interference in demanding industrial conditions. Powered by 5 V, it works with TTL logic and is compatible with popular platforms, and LED indicators facilitate diagnostics and integration.

A solar cell with a power output of 0.7 W and a voltage output of 5.5 V, measuring 95 x 95 x 3 mm, equipped with pads for soldering wires. Ideal for powering small electronic devices in DIY projects.

Li-Ion 18650 battery with a nominal voltage of 3.6V and a capacity of 3500mAh. It has protection against overcharging, excessive discharge, overload and short circuit.

The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5252

The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5255

Stereo camera module with USB interface. Equipped with an OV2710 CMOS sensor with a resolution of 2 MP working in the visible and infrared range. ArduCAM B0198

The universal multimeter allows you to measure direct and alternating voltage up to 250 V, direct current up to 10 A, resistance and temperature. Equipped with diode tester, circuit continuity test, automatic switch and automatic backlight. Uni-T UT131C

The universal multimeter allows you to measure direct and alternating voltage up to 250 V, direct current up to 10 A and resistance. Equipped with diode tester, circuit continuity test, automatic switch and automatic backlight. Uni-T UT131B

The universal multimeter allows you to measure direct and alternating voltage up to 250 V, direct and alternating current up to 10 A, resistance and capacity. Equipped with diode tester, circuit continuity test, automatic switch and automatic backlight. Uni-T UT131A

The universal multimeter allows you to measure direct and alternating voltage up to 600 V, direct and alternating current up to 20 A, resistance and capacity as well as frequency or peak values. Equipped with diode tester, continuity test, Hold function, automatic switch off and automatic backlight. Uni-T UT191E

Light ring with 32 RGB LEDs, type WS2812, controlled by a serial signal. The module can be powered by 5V, only one signal line is required to control it.

Light ring with 40 RGB LEDs, type WS2812, controlled by a serial signal. The module can be powered by 5V, only one signal line is required to control it.

Light ring with 60 RGB LEDs, type WS2812, controlled by a serial signal. The module can be powered by 5V, only one signal line is required to control it.