Best sellers

The Lanberg speaker cable 2x2.5 mm², 25 m in length with transparent insulation, is designed for connecting audio systems such as home theaters, car audio installations, and multi-room setups. Made of copper-clad aluminum (CCA), it ensures adequate sound quality for various applications. SC-2X25-10CC-0250-TR

The Lanberg speaker cable 2x4.0 mm², 25 m in length with transparent insulation, is designed for connecting audio systems such as home theaters, car audio installations, and multi-room setups. Made of copper-clad aluminum (CCA), it ensures adequate sound quality for various applications. SC-2X40-10CC-0250-TR

Sound terminal expansion board based on STA350BW for STM32 Nucleo

FeatherWing Proto - Prototyping Add-on For All Feather Boards

High-speed communication module powered by ADM582E. By communicating with the device via UART, users can take advantage of the RS485 communication protocol with speeds up to 16 Mbps. 410-310

2WD robot chassis made of plexiglass with a set of assembly elements (screws, bushes, nuts). The set includes motors, 65 mm wheels, support wheels and a battery pack

Raspberry Pi Prototype HAT is a prototype board that fits Raspberry Pi3, Pi 2 and + computers. The set includes a self-assembly connector and assembly elements

Low-power, 2.4GHz spectrum wireless protocol that you can use with iOS without needing special certification. Supported by all modern smart phones - excellent for use in portable projects that will make use of an iOS or Android phone or tablet; it also is supported in Mac OS X and Windows 8+. Adafruit 2995

GPS-13740

Arduino compatible shield for the ESP8266 WiFi SoC – a leading platform for Internet of Things (IoT) or WiFi-related projects. WRL-13287

Raspberry Pi 3 model B (Quad Core Broadcom BCM2837, 4x1.2GHz ARM Cortex-A53, RAM 1GB, 4xUSB, Ethernet, HDMI, Wifi, Bluetooth)

This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 36 V and efficiently reduces it to 7.5 V. The board measures only 0.7″ × 0.7″ yet delivers a typical continuous output current of up to 2.4 A and features reverse voltage protection.

Miniature micro-SD card reader with USB 2.0 interface. The reader\'s casing is made of aluminum, black. Works with both Windows and Mac OS

The Pmod TMP3 is an ambient temperature sensor built around the Microchip TCN75A. Users may configure the output through I²C to up to 12 bits of resolution as well as setting a trigger to occur when a user defined temperature threshold is reached.. Digilent 410-287

A small USB 2.0 hub that allows you to disable individual devices connected to its USB ports, as well as a visual evaluation of the number of devices enabled. It has a built-in connector for the external power supply, so it can act as an active hub. Cable with a length of 40cm, 4 USB ports

Red laser diode module with 5mW power, displaying intersecting lines. Ideally suited to the construction of the laser level, and thanks to the built-in driver, it is possible to power 3 - 5V. LD-G650A03 - Cross

The ring has sixteen RGB WS2812 diodes, controlled by means of serial signals. The module can be supplied with voltage from 4-7V, only one signal line is required to control it. NeoPixel Ring 16 x WS2812

Shield for STM32 Nucleo that allows you to add the possibility of operating a three-phase brushless motor (BLDC) or synchronous permanent magnet (PMSM). It uses the L6230 chip for control. X-NUCLEO-IHM07M1

ATTINY44A-PU

ATtiny44A-PU is a microcontroller from the AVR family in the DIP14 housing, it is equipped with memory: 2 kB Flash, 128 B SRAM, 128 B EEPROM. The power supply voltage is 4.5..5.5 V, the maximum clock speed is 20 MHz.