

zł69.49 tax excl.
The Pmod TMP3 is an ambient temperature sensor built around the Microchip TCN75A. Users may configure the output through I2C to up to 12 bits of resolution as well as setting a trigger to occur when a user defined temperature threshold is reached.. Digilent 410-287
Pmod™ devices are Digilent’s line of small I/O interface boards that offer an ideal way to extend the capabilities of programmable logic and embedded control boards. They allow sensitive signal conditioning circuits and high-power drive circuits to be placed where they are most effective - near sensors and actuators.
Pmod modules communicate with system boards using 6, 8, or 12-pin connectors that can carry multiple digital control signals, including SPI and other serial protocols. Pmod modules allow for more effective designs by routing analog signals and power supplies only where they are needed, and away from digital controller boards.
The Pmod TMP3 is an ambient temperature sensor built around the Microchip TCN75A. Users may configure the output through I2C to up to 12 bits of resolution as well as setting a trigger to occur when a user defined temperature threshold is reached.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
No product available!
No product available!
No product available!
No product available!
Module with digital thermal sensor, thermostat and I2C interface
Module with DS18B20 temperature sensor from Dallas Semiconductor. The sensor used allows you to measure temperatures in the range -55 ~ 125 ° C with an accuracy of ± 0.5 ° C (in the range of -10 ~ 85 ° C). The 1-Wire interface is used for communication. The plate is equipped with a goldpin connector and a KAMAMI connector, allowing easy connection of the module to the commissioning kits.
The module with the MCP9600 amplifier is designed to work with a thermocouple. The board is equipped with a Grove connector and communicates via I2C. Seeed Studio 101020594
No product available!
Module with CO2, temperature and humidity sensor SCD-41. Equipped with a Qwiic/STEMMA QT connector, it communicates via the I2C interface. Pimoroni PIM587
Temperature and humidity sensor module based on the HTS221 chip. Equipped with a STEMMA QT connector, it communicates via an I2C or SPI interface. Adafruit 4535
ST Microelectronics’ STTS22H digital temperature sensor module, featuring a Qwiic connector, offers accuracy from -40°C to 125°C without the need for additional calibration. The sensor consumes only 1.75 µA in single measurement mode, making it ideal for low-power applications, and additional features such as a configurable interrupt pin and the ability to select two I2C addresses increase its versatility. SparkFun SEN-21262
A module with a high precision temperature sensor based on the MCP9808 chip. It allows for measurements with an accuracy of ±0.25°C and communicates via the I2C interface. DFRobot SEN0435
Thermal camera module for Raspberry Pi offering precise temperature detection with 80x62 pixel resolution. It enables easy integration into industrial applications and control systems. It is ideal for temperature monitoring, thermal analysis and security systems. Waveshare Thermal-90 Camera HAT
No product available!
Module with DHT20 sensor. It allows you to measure humidity in the range from 0 to 100% and temperature from -40 to 80 ℃. Seeed Studio 101020932
Wireless, precise temperature sensor with high accuracy with built-in recorder. Works with thermoelectric sensors type K, J, T, N, E, B, S and R
Module with a DS18B20 temperature sensor with a measuring range from -55 to 125°C. It communicates via the 1-wire interface
A module with a temperature and humidity sensor based on the AHT20 system. Equipped with a Gravity connector, it communicates via the I2C interface. DFRobot SEN0528
Module with a non-contact IR temperature sensor. It allows the measurement in the range from -70 to 380°C and communicates via the I2C interface. Waveshare Infrared Temperature Sensor
A module with a temperature and humidity sensor based on the AHT20 system. It communicates via the I2C interface. DFRobot SEN0527
Module with a thermal imaging camera with an 80x42 field matrix and a 45° viewing angle. It is dedicated to work with the Raspberry Pi minicomputer and communicates via the SPI interface. Waveshare Thermal USB Camera
Set of sensors with cables. They can detect gestures, movement, touch, sound, and measure humidity, temperature, altitude and acceleration. SparkFun DEV-16156
No product available!
High temperature measuring kit. It consists of a signal conversion module with a range of -270°C to 1372°C and a K-type thermocouple probe with a range of up to 800°C. I2C communication DFRobot DFR0558
No product available!
Temperature sensor in the form of a HT-NTC100K thermistor on a 1 m cable. Designed for 3D printers
The Pmod TMP3 is an ambient temperature sensor built around the Microchip TCN75A. Users may configure the output through I2C to up to 12 bits of resolution as well as setting a trigger to occur when a user defined temperature threshold is reached.. Digilent 410-287