![LC filter for DC 0-25V 4A power supply](https://kamami.pl/67489-large_default/lc-filter-for-dc-0-25v-4a-power-supply.jpg)
![LC filter for DC 0-25V 4A power supply](https://kamami.pl/67489-large_default/lc-filter-for-dc-0-25v-4a-power-supply.jpg)
zł9.09 tax excl.
LC filter connected to the output of the DC power supply with a voltage from 0 to 25 V and a maximum current of 4 A. It reduces voltage ripple and interference caused by the power supply
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
LC filter connected to the output of the DC power supply. It is built on the basis of passive L (coils) and C (capacitors) elements. It can be used in low voltage DC power circuits from 0 to 25 V with a maximum current of 4 A. The filter reduces voltage ripple and reduces noise caused by the power supply. It is connected between the output of the power supply and the receiver and will be used, among others, in the case of powering audio amplifiers or industrial devices. The filters can be connected in series to increase the noise suppression effect or in parallel to increase the output current.
LC filter connected to the output of the DC power supply with a voltage from 0 to 50 V and a maximum current of 3 A. It reduces voltage ripple and interference caused by the power supply
LC filter connected to the output of the DC power supply with a voltage from 0 to 25 V and a maximum current of 2 A. It reduces voltage ripple and interference caused by the power supply
KAmodMMA7361LC is an accelerometer module with an analogue output, equipped with the MMA7361LC chip. It has a embedded voltage regulator, so it can be used in systems supplied with voltage of 2.5...5.5V.
Compact stepper motor controller with the TMC2208 system with operating voltage from 4 to 35 V. It offers smooth, quiet operation, high efficiency, various operating modes and easy configuration. It is controlled via the STEP/DIR interface and is an ideal solution for 3D printers and similar applications
Industrial module with 8 relays. It communicates via RS485 interface and supports Modbus RTU protocol. Waveshare Modbus RTU Relay (EN)
The trigger module is designed for chargers PD 2.0 and PD 3.0. It is equipped with a USB type C input and an output in the form of pads. Allows powering devices with 20V. PDC004
A module with a two-channel DC motor driver based on the TB6612FNG system. Designed for Wemos D1 Mini
4-channel module with relays designed to work with the Raspberry Pi Pico. It can switch signals up to 250 V AC and 7 A or 30 V DC and 10 A. SB Components 21178
No product available!
Bi-directional 8-channel logic level converter module (1.2-3.6V to 1.7-5.5V) based on TXB0108 chip.
Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi. This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5V. DFRobot DFR0553
Module with 8 relays SSR G3MC202P with a load up to 2 A. The board is equipped with a Grove connector and communicates via I2C. Seeed Studio 103020136
Powerful DC motor driver. It allows you to control a motor with a power supply voltage in the range of 6 ... 28 V, the motor can draw current of 100 A (using a heat sink). For the control PWM modeling (eg from RC receivers) is used in robotics, small electric vehicles or wherever there is a need to control a DC motor. Digilent 410-334-1
No product available!
Module with real-time clock and CR1225 battery socket for voltage backup. It communicates via the I2C interface. Seeed Studio 103030277
No product available!
Digital mono audio amplifier. It has one channel with a power of 30 W and can work with speakers from 4 to 8 Ω. It is powered with the voltage from 8 to 26 V.
The controller enables to supply the motors with voltage in the range of 10-47V and power consumption in continuous operation of 1.7A (4.5A peak) for each channel in dual or 3.4A mode (9A peak) in single channel mode. Pololu 2999
LC filter connected to the output of the DC power supply with a voltage from 0 to 25 V and a maximum current of 4 A. It reduces voltage ripple and interference caused by the power supply