![LC filter for DC 0-25V 3A power supply](https://kamami.pl/67480-large_default/lc-filter-for-dc-0-25v-3a-power-supply.jpg)
![LC filter for DC 0-25V 3A power supply](https://kamami.pl/67480-large_default/lc-filter-for-dc-0-25v-3a-power-supply.jpg)
zł8.86 tax excl.
LC filter connected to the output of the DC power supply with a voltage from 0 to 25 V and a maximum current of 3 A. It reduces voltage ripple and interference caused by the power supply
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
LC filter connected to the output of the DC power supply. It is built on the basis of passive L (coils) and C (capacitors) elements. It can be used in low voltage DC power circuits from 0 to 25 V with a maximum current of 3 A. The filter reduces voltage ripple and reduces noise caused by the power supply. It is connected between the output of the power supply and the receiver and will be used, among others, in the case of powering audio amplifiers or industrial devices. The filters can be connected in series to increase the noise suppression effect or in parallel to increase the output current.
LC filter connected to the output of the DC power supply with a voltage from 0 to 50 V and a maximum current of 4 A. It reduces voltage ripple and interference caused by the power supply
No product available!
LC filter connected to the output of the DC power supply with a voltage from 0 to 25 V and a maximum current of 4 A. It reduces voltage ripple and interference caused by the power supply
LC filter connected to the output of the DC power supply with a voltage from 0 to 50 V and a maximum current of 2 A. It reduces voltage ripple and interference caused by the power supply
LC filter connected to the output of the DC power supply with a voltage from 0 to 25 V and a maximum current of 2 A. It reduces voltage ripple and interference caused by the power supply
Module with 16 relays and 8 GPIO pins and 8 analog inputs. It communicates via the RS485, USB or Ethernet interface and supports the Modbus RTU/TCP protocol. Numato Lab NLRM1001-A
No product available!
Module with 4 relays with a maximum switching current of 7 A. It communicates via the USB interface. Numato Lab RL40001
Module with a 12 V relay and a timer. It allows you to turn the device on and off cyclically at a specified time using potentiometers. It can also operate in single trigger mode, which allows the device to be turned on after a signal has been applied for a specified period of time. The operating time can be adjusted from 1 s to 100 s or from 1 s to 15 min
Module with three voltage analog outputs ranging from 0 to 10 V. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP3079ADAM
HMI module with a 7" TFT color LCD display with a resolution of 800x480 px. Equipped with a capacitive touch panel. Communication via UART or GPIO interface. Nextion NX8048K070_011C
DC-DC Step-up converter module based on the U3V70F12 system. Input voltage 2.9-12V, output voltage 12V, maximum current 10A. Two mounting holes. Pololu 2895
Audio amplifier module with three output channels. It can be powered with the voltage from 18 to 24 VAC and has two outputs with a power of 100 W (left and right) and one with a power of 120 W (bass)
Pololu Simple High-Power Motor Controller 24v12 (Fully Assembled)
Module with 32 IO pins and 14 analog inputs. It communicates via the RS485, USB or Ethernet interface and supports the Modbus RTU/TCP protocol. The board is closed in an industrial housing. Numato Lab NLGM1005-A
No product available!
Laser rangefinder with measuring range up to 22m. The current consumption is up to 200mA and the supply voltage 4.5 ... 6V. Communication via UART or CAN interface. DFRobot SEN0238
The BMS module is designed for 5 Li-Ion cells. It is equipped with a micro USB and USB type C connector and supports fast charging (QC).
DC-DC Step-Down converter module with 5V output voltage and 1A output current. The module can be a replacement for the popular LM7805 regulator.
USB adapter designed for XBee modules. It can be connected to a computer with a USB cable and used with the X-CTU software to configure the XBee. DFRobot DFR0174
The Step-Up/Step-DownS7V8F5 Buck Voltage Regulator module with output voltage 5V, input voltage range of 2.7-11.8V and a maximum output current of 0.5-1A. Pololu 2123
3-channel voltage and current monitoring module designed to work with the Raspberry Pi. It can measure voltage ranging from 0 to 26 V and voltage ± 3.2 A. SB Components 20805
Module with digital thermal sensor, thermostat and I2C interface
LC filter connected to the output of the DC power supply with a voltage from 0 to 25 V and a maximum current of 3 A. It reduces voltage ripple and interference caused by the power supply