![LC filter for DC 0-50V 2A power supply](https://kamami.pl/67482-large_default/lc-filter-for-dc-0-50v-2a-power-supply.jpg)
![LC filter for DC 0-50V 2A power supply](https://kamami.pl/67482-large_default/lc-filter-for-dc-0-50v-2a-power-supply.jpg)
zł8.86 tax excl.
LC filter connected to the output of the DC power supply with a voltage from 0 to 50 V and a maximum current of 2 A. It reduces voltage ripple and interference caused by the power supply
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
LC filter connected to the output of the DC power supply. It is built on the basis of passive L (coils) and C (capacitors) elements. It can be used in low voltage DC power circuits from 0 to 50 V with a maximum current of 2 A. The filter reduces voltage ripple and reduces noise caused by the power supply. It is connected between the output of the power supply and the receiver and will be used, among others, in the case of powering audio amplifiers or industrial devices. The filters can be connected in series to increase the noise suppression effect or in parallel to increase the output current.
LC filter connected to the output of the DC power supply with a voltage from 0 to 50 V and a maximum current of 4 A. It reduces voltage ripple and interference caused by the power supply
No product available!
LC filter connected to the output of the DC power supply with a voltage from 0 to 25 V and a maximum current of 4 A. It reduces voltage ripple and interference caused by the power supply
LC filter connected to the output of the DC power supply with a voltage from 0 to 50 V and a maximum current of 3 A. It reduces voltage ripple and interference caused by the power supply
The Step-Up Buck Voltage Regulator module with output voltage of 3.3V and input voltage range of 1-3V and a maximum output current of 200 mA. SparkFun PRT-10967
No product available!
Audio module based on a 32-bit PCM5102A DAC converter intended for cooperation, among others with Raspberry Pi minicomputers. Communication via the I2S interface. GY-PCM5102
No product available!
This compact breakout board for Maxim’s MAX14870 motor driver offers a wide operating voltage range of 4.5 V to 36 V and can deliver a continuous 1.7 A (2.5 A peak) to a single brushed DC motor. It features a simple two-pin speed/direction interface and built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature.
Module with the driver of motors TB6612FNG and driver PWM PCA9685 for Raspberry Pi Pico. It allows you to control the movement of 4 DC motors. Waveshare Pico-Motor-Driver
UART-RS232 converter module. The board was equipped with a Grove and DB9 connector. Seeed Studio 103020192
No product available!
Module with a 16-channel GPIO expander with the ability to control LEDs. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4886
Camera module with 5MP USB interface and IMX335 sensor. Equipped with manual focus. Waveshare IMX335 5MP USB Camera (A)
No product available!
Module with a capacitive fingerprint sensor for the Raspberry Pi. It communicates via the UART or USB interface. SB Components 21253
Single-channel DC motor driver with an operating voltage from 10 to 45 V and a continuous current up to 40 A. It can be controlled by an analog signal, PWM, UART, RC or by means of built-in buttons. Cytron MDS40B
Stereo audio amplifier based on the TPA3116D2 chip. It can be powered with the voltage from 12 to 24 V and has two outputs with a power of 100 W
Universal driver for DC and LED motors. It can work with a supply voltage from 5 V to 24 V and a load up to 10 A. DFRobot DRI0050
No product available!
Two axis stepper motor driver expansion board based on the L6470 for STM32 Nucleo
Pololu MQ Gas Sensor Carrier
Module with 2-channel DC motor driver DRV8833 designed to work with the Raspberry Pi Pico. It can work with a voltage from 2.7 to 10.8 V and a current of up to 1.2 A. Pimoroni PIM617
MEMS MSM261S4030H0 microphone module designed to work with Sipeed MAix kits. The module is characterized by high sensitivity, low noise and low cost. Seeed Studio 107990153
LC filter connected to the output of the DC power supply with a voltage from 0 to 50 V and a maximum current of 2 A. It reduces voltage ripple and interference caused by the power supply