

zł261.11 tax excl.
Universal USB2.0 adapter for JTAG, UART and GPIO based on the FTDI FT2232H chip. The adapter card converts signals from USB2.0 to standard serial or parallel interfaces of embedded systems such as JTAG, SPI, I²C and UART. Compatible with Xilinx tools. Trenz TE0790-03
Universal USB2.0 adapter for JTAG, UART and GPIO based on the FTDI FT2232H chip. The adapter card converts signals from USB2.0 to standard serial or parallel interfaces of embedded systems such as JTAG, SPI, I²C and UART.
The module is equipped with a programmable CPLD system controller supplied by Lattice XO2-256 CPLD to control the signals of configured interfaces. The USB 2.0 data stream can also be converted to 8 independent GPIOs or used as FIFO.
EEPROM is pre-programmed and recognized by all Xilinx tools (ISE / Impact / Chipscope, Vivado Programmer / SDK).
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Adapter for 20/14/10-pin JTAG. It allows to connect the JTAG programmer to a evaluation boards which uses various standards of the programming connector. IDC20, IDC14, IDC10 and JST-XH sockets are available.
JTAG interface galvanic separator that protects equipment against damage caused by potential differences, with a maximum clock frequency of 110 MHz, 3-5 V power supply, and isolation voltage up to 1 kVDC, equipped with multiple connectors and optical status signaling
Module with Xilinx Kintex-7 XC7K70T-2CF system, 32MB FLASH memory and very fast data transmission systems. Everything is on a small 4 x 5 cm plate. TE0741-03-070-2CF
No product available!
Module with Xilinx Kintex-7 XC7K160T-2IF chip, 32MB FLASH memory and very fast data transmission systems. Everything is on a small 4 x 5 cm plate. TE0741-03-160-2IF
No product available!
Module with Xilinx Kintex-7 XC7K325T-2CF system, 32MB FLASH memory and very fast data transmission systems. Everything is on a small 4 x 5 cm plate. TE0741-02-325-2CF
No product available!
TE0706 is a base plate for Trenz Electronic 4x5cm Muduors. It allows you to connect USB, JTAG and Ethernet interfaces. TE0706-02
No product available!
Base plate for Trenz Electronics modules 4 x 5 cm, eg for TE0741. The board allows connecting to the module interfaces: USB, Ethernet, JTAG, UART. TE0703-06
No product available!
Module with Xilinx Artix-7, USB 3.0 / FIFO bridge, 1GB DDR3L SDRAM memory, 32 MB flash memory and pulse converters to ensure all voltages in the system. Everything fits on a small 4 x 5 cm tile. TE0713-01-200-2C
No product available!
Module with Xilinx Kintex-7 XC7K410T-2CF system, 32MB FLASH memory and very fast data transmission systems. Everything is on a small 4 x 5 cm plate. TE0741-03-410-2CF
No product available!
Module with Xilinx Artix-7 100T system, FLASH memory with 32 MB capacity, 1 GB RAM memory and 10/100 Mbit Ethernet controller. Everything fits on a small 4 x 5 cm tile. TE0712-02-100-2C
No product available!
Base plate for Trenz Electronic 4 x 5 cm modules. It allows you to connect an FPGA system through board-to-board connections to external peripherals to test and develop software. TE0701-06
No product available!
Module with Xilinx Kintex-7 XC7K70T-2CF system, 32MB FLASH memory and very fast data transmission systems. Everything is on a small 4 x 5 cm plate. TE0741-03-070-2CF
No product available!
Module with Xilinx Artix-7 100T system, FLASH memory with 32 MB capacity, 1 GB RAM memory and 10/100 Mbit Ethernet controller. Everything fits on a small 4 x 5 cm tile. TE0712-01-100-2C
No product available!
Base plate designed to work with TE0745 modules. TEB0745-02
No product available!
Module with Xilinx Kintex-7 XC7K70T-2IF chip, 32MB FLASH memory and very fast data transmission systems. Everything is on a small 4 x 5 cm plate. TE0741-03-070-2CF
No product available!
Module with Xilinx Artix 7 35T system, two 100 MBit Ethernet circuits, 512 MB RAM memory, 32 MB flash memory and built-in voltage converters. TE0710-02-35-2CF
No product available!
Module with Xilinx Artix-7 15T system, 32MB FLASH memory and 8MB HyperRAM memory. TE0725-03-15-1C
No product available!
Base plate designed to work with TE0808 and TE0803 modules. It allows you to connect the module to external connectors and interfaces. TEBT0808-02
No product available!
Module with Xilinx Artix-7 100T system, 32MB FLASH memory and very fast data transmission systems. Everything is on a small 4 x 5 cm plate. TE0741-03-160-2CF
No product available!
Module with Xilinx Kintex-7 XC7K325T-2CF system, 32MB FLASH memory and very fast data transmission systems. Everything is on a small 4 x 5 cm plate. TE0741-03-325-2CF
No product available!
Industrial SoC module integrating Xilinx Zynq 7020 SoC, Gigabit Ethernet transceiver, 1 GB DDR3 SDRAM and 32 MB Flash memory. Trenz Electronic TE0720-03-2IF
No product available!
Universal USB2.0 adapter for JTAG, UART and GPIO based on the FTDI FT2232H chip. The adapter card converts signals from USB2.0 to standard serial or parallel interfaces of embedded systems such as JTAG, SPI, I²C and UART. Compatible with Xilinx tools. Trenz TE0790-03