

RGB WS2812B LED matrix with 1mm pitch
Description:
The three-color LED WS2812B (RGB) matrix.
A special feature of the WS2812B diodes is the RGB controller in the structure, which interprets the signals from the diode input (6-pin housing) and at the right moment shifts them to its output or controls the LED structure.
Each of the diodes is connected in series with an adjacent one (signal output to the entrance of an adjacent diode), thanks to which the whole creates a 256-cell shift register. Control of the entire matrix takes place via a single wire, to which the pulses are suitably formed, addressing the kolen of the WS2812B diodes. After addressing the entire diode array (after 256 shifts of values to subsequent diodes), there is a pulse allowing the display of the contents of each cell (diodes WS2812B), thus creating an 8x32 image.
The matrix has three connectors; input, output and additional power connector. The matrices can be combined into series (bearing in mind the technical limits of the control system and matrices). It is also possible to connect the matrix with a tape or other module with a WS2812B diode.
The WS2812B LED can display 16777216 colors (256 intensity levels of each RGB component).
Features:
To download:
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
LED RGB WS2812B, Black Strip, 5m, 60LEDs / m, waterproof IP67
Matrix with 16 WS2812B RGB diodes controlled by a serial signal. The module can be powered with 5V, only one signal line is required for control
32 x 64 RGB LED display module (2048 LEDs). Refresh rate 1:16. It has two IDC connectors, which allows you to connect multiple displays in series. SparkFun COM-14718
3 mm LED matrix. The matrix contains 35 LEDs (5x7 system) in red. The diodes are connected by a common cathode.
Flexible 8x8 RGB LED matrix module. The set uses addressable SK6812/WS2812B diodes. DFRobot DFR0461
No product available!
9x16 Charlieplexed LEDs designed to match with the Adafruit 16x9 Charlieplexed PWM LED Matrix Driver - IS31FL3731. Color: YELLOW. Adafruit 2948
No product available!
This is the tiniest little LED grid, with 64 full RGB color pixels in a square. For use with Arduino and Raspberry Pi. Adafruit 3444
No product available!
Module with 5x5 RGB LED matrix display (25 LEDs). It uses the IS31FL3731 driver and communicates via the I2C interface. Pimoroni PIM435
Module with 16x10 RGB LED matrix display (160 diodes) designed to work with the Raspberry Pi Pico. Communicates via a digital interface. Waveshare Pico-RGB-LED
Module with 17x7 LED matrix display (119 LEDs) designed to work with the Raspberry Pi. It uses the IS31FL3731 driver and communicates via the I2C interface. Pimoroni PIM491
No product available!
RGB LED matrix module with 64 APA102-2020 diodes in 8x8 arrangement. It is powered by 5V by the pads located on the bottom of the board and controlled by the SPI interface. SparkFun COM-15047
A circular board for the BBC micro:bit with 24 addressable ZIP LEDs, offering a full color spectrum and allowing for the creation of eye-catching lighting animations. Mounts directly to the micro:bit using screws, and additional pins allow for the connection of sensors or additional LEDs. Power is supplied via a JST socket or solder pads, and the built-in regulator also powers the micro:bit. The ZIP Halo is fully compatible with NeoPixel libraries and can be programmed in MakeCode or MicroPython. Kitronik 5625
RGB LED WS2812B 8 x 4 matrix module for Raspberry Pi, one signal pin, additional power connector, direct RPI computer overlay. Waveshare RGB LED HAT
No product available!
Matrix with 25 WS2812B RGB diodes controlled by a serial signal. The module can be powered by 5V, only one signal line is required for control
An 8x8 panel with 64 addressable RGB LEDs, designed to work with the BBC micro:bit. It allows you to display text, animations, and lighting effects in full color, and thanks to the expansion connectors, multiple boards can be connected to create larger displays. The module is powered by a JST connector with a built-in regulator, and its design protects the micro:bit from overload. The ZIP Tile is easy to use thanks to MakeCode blocks and is ideal for educational projects, hobby projects, and interactive installations. Kitronik 5645
The module with an 8x8 LED matrix designed for Wemos D1 Mini
RGB WS2812B LED matrix with 1mm pitch