Order and pay in
for same day shipping
The Uni-T non-contact thermometer is designed to measure the temperature...
Evaluation kit with LittleBee GW1N-1 FPGA chip. Offers 1152 LUTs and 864...
Flexible adapter for microSD to SD card with a length of 25 cm. Supports...
Step-Down converter module with input voltage from 4.75 to 23V, output...
Evaluation kit with LittleBee GW1NR9 FPGA. It offers 8640 LUTs, 6480...
Flexible extension for a microSD card with a length of 25 cm. Supports...
Vorel - 40056
5:1 Micro Metal Gearmotor HP
|DC motor power||HP|
|Rotation speed||6 100 RPM|
|Shaft diameter||3 mm|
|Obustronny wał silnika||Nie|
|Power supply voltage||6V|
5:1 Micro Metal Gearmotor HP
This gearmotor is a miniature (0.94" x 0.39" x 0.47"), high-power brushed DC motor with 5:1 metal gearbox, similar to Sanyo’s popular 12 mm gearmotors. These units have a 0.365"-long, 3 mm-diameter D-shaped output shaft.
Key specs at 6 V: 6000 RPM and 120 mA free-run, 2 oz-in (0.1 kg-cm) and 1.6 A stall.
These tiny brushed DC gearmotors are intended for use at 6 V, though in general, these kinds of motors can run at voltages above and below this nominal voltage, so they should comfortably operate in the 3 – 9 V range (rotation can start at voltages as low as 0.5 V). Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor. The micro metal gearmotors are available in a wide range of gear ratios—from 5:1 up to 1000:1—and offer a choice between two different motors: high-power (HP) and standard. With the exception of the 1000:1 gear ratio versions, all of the micro metal gearmotors have the same physical dimensions, so one version can be easily swapped for another if your design requirements change. Please see the micro metal gearmotor comparison table for detailed specifications of all our micro metal gearmotors. This dynamically-sortable table can help you find the gearmotor that offers the best blend of speed, torque, and current-draw for your particular application. A more basic comparison table is available below.
Some versions of the gearmotors are sold with an additional 1mm-diameter output shaft that protrudes from the rear of the motor. This 4.5mm-long rear shaft rotates at the same speed as the input to the gearbox and offers a way to add a custom-built encoder to provide motor speed or position feedback.
Gearbox Shaft Only
Gearbox & Motor Shaft
|5:1||6000 RPM||2 oz-in||1600 mA||5:1 micro HP|
|2500 RPM||1 oz-in||360 mA||5:1 micro|
|10:1||3000 RPM||4 oz-in||1600 mA||10:1 micro HP||10:1 micro HP|
|1300 RPM||2 oz-in||360 mA||10:1 micro|
|30:1||1000 RPM||9 oz-in||1600 mA||30:1 micro HP||30:1 micro HP|
|440 RPM||4 oz-in||360 mA||30:1 micro||30:1 micro|
|50:1||625 RPM||15 oz-in||1600 mA||50:1 micro HP||50:1 micro HP|
|250 RPM||7 oz-in||360 mA||50:1 micro||50:1 micro|
|75:1||400 RPM||22 oz-in||1600 mA||75:1 micro HP|
|170 RPM||9 oz-in||360 mA||75:1 micro|
|100:1||320 RPM||30 oz-in||1600 mA||100:1 micro HP||100:1 micro HP|
|120 RPM||12 oz-in||360 mA||100:1 micro||100:1 micro|
|150:1||200 RPM||40 oz-in||1600 mA||150:1 micro HP|
|85 RPM||17 oz-in||360 mA||150:1 micro|
|210:1||140 RPM||50 oz-in||1600 mA||210:1 micro HP|
|60 RPM||27 oz-in||360 mA||210:1 micro|
|250:1||120 RPM||60 oz-in||1600 mA||250:1 micro HP|
|50 RPM||32 oz-in||360 mA||250:1 micro|
|298:1||100 RPM||70 oz-in||1600 mA||298:1 micro HP||298:1 micro HP|
|45 RPM||40 oz-in||360 mA||298:1 micro||298:1 micro|
|1000:1||32 RPM||125 oz-in||1600 mA||1000:1 micro HP|
|14 RPM||70 oz-in||360 mA||1000:1 micro|
Note: The 1000:1 gearmotors can generate enough torque to damage themselves. The stall torque values given for those two motors are theoretical, and we strongly recommend you avoid stalling them.
|Micro metal gearmotor dimensions (units in mm).|
The gearbox has a long (0.365" or 9.27 mm), 3 mm-diameter D-shaped metal output shaft, and the brass faceplate has two mounting holes threaded for M1.6 screws (1.6 mm diameter, 0.35 mm thread pitch). It weighs approximately 0.35 oz (10 g). Versions with the extended motor shaft have a 1mm diameter round shaft that protrudes 4.5 mm from the rear of the motor, between the two motor terminals; this is not pictured in the above dimension diagram.
Note: The gearbox on the 1000:1 and 1000:1 HP micro metal gearmotors is 12.5 mm long. All of the other micro metal gearmotors have 9mm-long gearboxes, as shown in the above dimension diagram.
We offer a wide selection of metal gearmotors that offer different combinations of speed and torque. Our metal gearmotor comparison table can help you find the motor that best meets your project’s requirements.
|Some of the Pololu metal gearmotors.|
|Pololu Micro Metal Gearmotor Bracket Pair - Black|
|10:1 Micro Metal Gearmotor HP|
|Pololu 42x19mm Wheel and Encoder Set|