Motoron M3S550 Triple Motor Controller Shield - 3-channel DC motor controller for Arduino (for assembly)
ID: 1185706
5902186316935
zł132.34
Tax included
zł107.59 tax excl.
DC motor controller that allows the movement of three drives to be controlled via an I2C interface. A board with connectors for mounting is included. Pololu 5069
Description
DC motor driver dedicated to Arduino boards. It allows you to control the movement of three drives using the I2C interface. It can work with motors with a supply voltage from 1.8 to 22 V and has a capacity of up to 1.7 A per motor (continuous operation). The controller has a built-in protection in the event of loss of communication with Arduino and the ability to configure the response if an error occurs. The user can set the maximum acceleration and the starting speed of the motor, and the shield construction allows you to connect the drivers with each other. The manufacturer's website includes a user manual and a library with sample programs.
Features
- Operating voltage range: 1.8 V to 22 V
- Maximum output current per motor: 1.7 A continuous, 5 A instantaneous
- Voltage range of the logic part: 2.8 V to 5.5 V
- Control interface: I2C
- I2C clock frequency: up to 400 kHz
- CRC control capability
- Configurable motion parameters:
- Maximum acceleration/deceleration
- Initial speed
- Delay for change of direction
- PWM frequency: eight options available from 1 kHz to 80 kHz
- Protection in case of communication loss
- Configurable automatic error response
- Measurement of motor supply voltage (VIN)
- Possibility to power the Arduino directly or via an external stabiliser (not supplied)
- Two status LEDs
- Motor direction LEDs
Kit contains
- Motoron M3S550 Triple Motor Controller Shield
- Connector 1x10 straight female
- Connector 1x8 straight female
- 4 x 2pin 3.5 mm screw connector
- 4 x 2pin 5 mm screw connector
- Connector 1x25 straight male
1185706
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.57
24h
Available quantity: 243
Available
A set with ATmega2560 microcontroller (256 kB Flash, 8 kB RAM, 4 kB EEPROM) clocked at 16 MHz. The user has, among others: 54 I / O lines, 14 PWM channels, 16 analog inputs. Arduino A000067
zł189.00
Delivery date unknown
No product available!
DC motor controller that allows the movement of three drives to be controlled via an I2C interface. A board without connectors is included. Pololu 5070
zł106.27
24h
Available quantity: 2
Available
DC motor controller that allows the movement of three drives to be controlled via an I2C interface. A board with connectors for mounting is included. Pololu 5069
zł132.34
24h
Available quantity: 2
Available
Other products in the same category (16)
Pololu Dual MC33926 Motor Driver Shield for Arduino
zł197.80
24h
Available quantity: 2
Available
Nano Motor Carrier to moduł rozszerzeń przeznaczony do Arduino Nano 33 IoT, który został zaprojektowany, aby ułatwić sterowanie silnikami. Pozwala na kontrolowanie ruchu czterech silników prądu stałego, ale można go również wykorzystać do podłączenia serwomechanizmów i czujników. Arduino ABX00041
zł285.57
24h
Available quantity: 1
Available
SimpleFOC Shield Type B enables precise control of BLDC motors using FOC technology, supporting supply voltages up to 35 V and working with Arduino and STM32. The module is equipped with INA240 current sensors and an IR2104 driver with configurable gate voltage, allowing precise motion control in robotics and automation projects.
zł114.64
24h
Available quantity: 2
Available
This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 V operating range and are efficient enough to deliver a continuous 18 A without a heat sink.
zł288.26
24h
Available quantity: 1
Available
This Kit with fully-dedicated PWM driver chip handles all the motor and speed controls over I2C. Only two data pins (SDA & SCL in addition to the power pins GND & 5V) are required to drive the multiple motors; you can also connect any other I2C devices or shields to the same pins. This makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3. Adafruit 1438
zł102.94
24h
Available quantity: 3
Available
Shield with DC motor driver for Arduino. It has an operating voltage of 7 to 30 V and a maximum continuous current of 10 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron SHIELD-MD10
zł59.91
24h
Available quantity: 2
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5045
zł456.85
4 weeks
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5040
zł327.65
4 weeks
No product available!
DC motor controller that allows the movement of three drives to be controlled via an I2C interface. A board without connectors is included. Pololu 5070
zł106.27
24h
Available quantity: 2
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for self-assembly. Pololu 5046
zł435.53
4 weeks
No product available!
Motoron M3S256 Triple Motor Controller Shield - 3-channel DC motor driver for Arduino (for assembly)
DC motor driver that allows you to control the movement of three drives using the I2C interface. Plate with connectors for assembly. Pololu 5031
zł202.77
4 weeks
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5041
zł302.08
4 weeks
No product available!
An Arduino extension that allows you to simultaneously control four DC motors, two stepper motors, or two 5V servos. It uses an L293D chip, which provides stable operation and a current of up to 1.2A per channel at motor voltages of 4.5-12V. An 8-stage shift register reduces the number of pins needed for control, allowing for more efficient use of microcontroller resources. Elecrow Four Channels Motor Shield
zł11.89
24h
Available quantity: 1
Available
Dual-channel electric motors controller (H-bridge) Arduino Motor Shield Rev3 with L298 for controlling two DC motors or one stepper motor with the possibility of using an electronic brake.
zł143.53
3 weeks
No product available!
Pololu - 2511
zł41.29
24h
Available quantity: 1
Available
Dual MAX14870 Motor Driver is a dual DC motor controller compatible with the Arduino standard that allows you to control two DC motors with 4.5 ... 36V continuous current of 1.7A. Polol 2519
zł134.43
24h
Available quantity: 2
Available
DC motor controller that allows the movement of three drives to be controlled via an I2C interface. A board with connectors for mounting is included. Pololu 5069