

zł232.17 tax excl.
Nano Motor Carrier to moduł rozszerzeń przeznaczony do Arduino Nano 33 IoT, który został zaprojektowany, aby ułatwić sterowanie silnikami. Pozwala na kontrolowanie ruchu czterech silników prądu stałego, ale można go również wykorzystać do podłączenia serwomechanizmów i czujników. Arduino ABX00041
Nano Motor Carrier is an extension module designed for the Arduino Nano 33 IoT, which has been designed to facilitate the control of motors. It allows you to control the motion of four DC motors, but can also be used to connect servos and sensors using 3-pin male connectors. Among the functionality of the board, the user will also find a 9-axis IMU sensor (accelerometer, gyroscope and magnetometer) and a charger for single-cell lithium-ion batteries. The module also allows you to connect two quadrature encoders. When working with motors, an external power source is needed to power the controllers and motors. This can be done by connecting a 1-cell Lithium Ion battery to the battery connector or by using an external power source. The manufacturer provides the Arduino Motor Carrier library available from the library manager, which greatly facilitates the start of programming and motor control.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Board with nRF52840 microcontroller with Cortex M4F core (64 MHz, 1 MB Flash, 256 kB RAM). Equipped with BT 5.0 and IMU LSM9DS1 module. Module with headers. Arduino ABX00034
Board with SAMD21 microcontroller with CortexM0 + core (48 MHz, 256 KB Flash, 32 KB RAM). Equipped with WiFi and BT module (based on ESP32) and IMU LSM6DS3 unit. Ideal for applications in the IoT area. Module with headers. Arduino ABX00032
NINA B306 BLE module board based on the nRF52840 microcontroller with CortexM4F core (64 MHz, 1 MB Flash, 256 kB RAM). Equipped with sensors - 9-axis IMU, temperature, pressure, humidity, light, colour, gesture and microphone. Arduino ABX00070
No product available!
Shield with dual-channel DC motor driver for Arduino. It has an operating voltage from 7 to 30 V and a continuous current of up to 1.2 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron SHIELD-3AMOTOR
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5041
No product available!
Dual-channel electric motors controller (H-bridge) Arduino Motor Shield Rev3 with L298 for controlling two DC motors or one stepper motor with the possibility of using an electronic brake.
DC motor driver that allows you to control the movement of three drives using the I2C interface. Plate with connectors for assembly. Pololu 5031
No product available!
DC motor controller that allows the movement of three drives to be controlled via an I2C interface. A board without connectors is included. Pololu 5070
Pololu - 2511
DRV8825 Stepper Motor Driver Module for Arduino. It allows you to control two drives, equipped with an XBee connector. DFRobot DRI0023
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5040
No product available!
(DRI0009) 2A Motor Shield For Arduino
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for self-assembly. Pololu 5037
No product available!
This Kit with fully-dedicated PWM driver chip handles all the motor and speed controls over I2C. Only two data pins (SDA & SCL in addition to the power pins GND & 5V) are required to drive the multiple motors; you can also connect any other I2C devices or shields to the same pins. This makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3. Adafruit 1438
DC motor driver that allows you to control the movement of three drives using the I2C interface. Board with soldered connectors. Pololu 5030
No product available!
Extension module for building a 3D printer or CNC machine compatible with Arduino. The kit includes four A4988 stepper motor drivers. the module is supplied with the voltage from 12 to 36 V
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5044
No product available!
Quad DC Motor Driver Shield is an Arduino compatible DC motor driver that allows you to control 4 DC motors with a voltage between 2.5 ... 13.5V and up to 1.2A. DFRobot DRI0039
Two axis stepper motor driver expansion board based on the L6470 for STM32 Nucleo
Nano Motor Carrier to moduł rozszerzeń przeznaczony do Arduino Nano 33 IoT, który został zaprojektowany, aby ułatwić sterowanie silnikami. Pozwala na kontrolowanie ruchu czterech silników prądu stałego, ale można go również wykorzystać do podłączenia serwomechanizmów i czujników. Arduino ABX00041