![VS1053 Codec + MicroSD Breakout - MP3/WAV/MIDI/OGG Play + Record - v4 VS1053 Codec + MicroSD Breakout - MP3/WAV/MIDI/OGG Play + Record - v4](https://kamami.pl/17268-large_default/vs1053-codec-microsd-breakout-mp3wavmidiogg-play-record-v4.jpg)
![VS1053 Codec + MicroSD Breakout - MP3/WAV/MIDI/OGG Play + Record - v4 VS1053 Codec + MicroSD Breakout - MP3/WAV/MIDI/OGG Play + Record - v4](https://kamami.pl/17268-large_default/vs1053-codec-microsd-breakout-mp3wavmidiogg-play-record-v4.jpg)
zł107.84 tax excl.
This breakout board, the ultimate companion for the VLSI VS1053B DSP codec chip, can decode a wide variety of audio formats MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM and ADPCM); it can be used to record audio in both PCM (WAV) and compressed Ogg Vorbis. 8 GPIO pins can be used for lighting up small LEDs or reading buttons. Adafruit 1381
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
This breakout board is the ultimate companion for the VLSI VS1053B DSP codec chip. The VS1053 can decode a wide variety of audio formats such as MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM and ADPCM). It can also be used to record audio in both PCM (WAV) and compressed Ogg Vorbis. You can do all sorts of stuff with the audio as well such as adjusting bass, treble, and volume digitally. There is also 8 GPIO pins that can be used for stuff like lighting up small LEDs or reading buttons.
All this functionality is implemented in a light-weight SPI interface so nearly any microcontroller can play audio from an SD card. Theres also a special MIDI mode that you can boot the chip into that will read classic 31250 kbaud MIDI data on a UART pin and act like a synth/drum machine - there are dozens of built-in drum and sample effects! But the chip is a pain to solder, and needs a lot of extras. Thats why we spun up the best breakout, perfect for use with an Arduino but also good for other microcontrollers that just dont have the computational power to decode MP3s.
The breakout is slim enough to fit on a breadboard with 1 row of holes left over for wiring. Theres 3.3V and 1.8V regulators onboard with ferrite beads and analog filtering for quality analog output. Theres a microphone input port that you can wire up a line-in or mic to and record compressed audio. All 8 GPIO are broken out and they all have built in 100K pulldowns, simply connect your button from the GPIO pin to 3.3V for an active-high connection. Youll likely want to play music from a microSD card so we added a holder on-board. And since we know so many of our customers use 5 V microcontrollers like the Arduino, we made the interface pins all 5V compliant with level shifters so you can use the chip at 3V or 5V power/logic!
Bluetooth 4.1 audio receiver with 3.5mm Jack audio output. It allows you to play files via Bluetooth, from a mass memory (flash drive), from a computer via USB or from a microSD card
Module with a multi-channel WAV player. It allows you to mix 32 mono or 18 stereo tracks with the ability to connect to any MIDI controller. It has 8 mono or 4 stereo audio outputs. SparkFun WIG-18159
No product available!
Audio receiver with Bluetooth 4.2 module. It is powered by a microUSB connector or a battery and is equipped with a charging circuit
WM8960 stereo codec module with driver for 1W class D speakers and headphones. It uses the I2S interface and the I2C bus to configure the system. SparkFun BOB-21772
Audio module based on a 32-bit PCM5102A DAC converter intended for cooperation, among others with Raspberry Pi minicomputers. Communication via the I2S interface. GY-PCM5102
No product available!
Audio module with DAC, line output and display, designed to work with the Raspberry Pi. Pimoroni PIM483
Bluetooth audio receiver module that allows wireless transmission of sounds. It is equipped with a PCB antenna and edge connectors
MP3 player with support for microSD cards and USB memory. It can work as a separate device and play sounds from a card or pendrive
No product available!
Audio player module with MP3 decoder and microSD card slot. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 107020069
No product available!
Bluetooth 4.1 audio receiver with 3.5mm Jack audio output. It allows you to play files via Bluetooth, from mass memory (pendrive) or microSD card and supports WAV, APE, MP3 and FLAC formats. XY-BT-L
No product available!
Mini MP3 player with 128 MB built-in memory. It can work as a separate device and play sounds or be controlled via the UART serial interface. DFRobot DFR0768
No product available!
WM8960 stereo codec module with driver for 1W class D speakers and headphones. It uses the I2S interface and the I2C bus to configure the system. SparkFun BOB-21250
Expansion module with stereo audio output equipped with LM4550 chip with AC\'97 codec. It allows you to play and record high-quality stereo sounds. Numato Lab EXPAUD003
Bluetooth 4.2 audio receiver with 3.5 mm jack audio output. It allows you to play files via Bluetooth and supports WAV, WMA APE, MP3 and FLAC formats. MH-M28
The audio module with the PCM5100A DAC converter is designed to work with the Raspberry Pi. Pimoroni PIM542
This breakout board, the ultimate companion for the VLSI VS1053B DSP codec chip, can decode a wide variety of audio formats MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM and ADPCM); it can be used to record audio in both PCM (WAV) and compressed Ogg Vorbis. 8 GPIO pins can be used for lighting up small LEDs or reading buttons. Adafruit 1381