- Out-of-Stock
MAG3110FCR1
ID: 184737
3-axis digital magnetometer, I2C, DFN10, Freescale, RoHS
MAG3110FCR1
3-axis digital magnetometer, I2C, DFN10, Freescale, RoHS
The MAG3110 is a small, low-power, 3-axis digital magnetometer. The MAG3110 magnetometer measures the three components of the local magnetic field which will be the sum of the geomagnetic field and the magnetic field created by components on the circuit board.
The MAG3110 features a standard I2C serial interface and is capable of measuring local magnetic fields up to 1000 uT with output data rates (ODR) up to 80 Hz. The combination of the magnetometer with the accelerometer provides a full tilt-compensated electronic compass capability. With a GPSenabled device, direction-dependent locationbased services can be achieved.
3-axis digital magnetometer, I2C, DFN10, Freescale, RoHS
The MAG3110 is a small, low-power, 3-axis digital magnetometer. The MAG3110 magnetometer measures the three components of the local magnetic field which will be the sum of the geomagnetic field and the magnetic field created by components on the circuit board.
The MAG3110 features a standard I2C serial interface and is capable of measuring local magnetic fields up to 1000 uT with output data rates (ODR) up to 80 Hz. The combination of the magnetometer with the accelerometer provides a full tilt-compensated electronic compass capability. With a GPSenabled device, direction-dependent locationbased services can be achieved.
184737
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Freescale starter kit with Kinetis KL25Z family microcontroller (Cortex-M0 +), integrated with the programmer-debugger OpenSDA, capacitive switch, LED-RGB and MEMS 3D accelerometer. Arduino-compatible outputs.
zł139.00
Delivery date unknown
No product available!
Other products in the same category (16)
MYIR MYIR MYS-7Z010-LC is a set of elements with a single board computer based on the Xilinx XC7Z010-1CLG400C (Zynq-7010) system. This system consists of a dual-core processor based on Cortex-A9 core, which can operate at a maximum frequency of 667 MHz. The computer is equipped with 512 MB of DDR3 SDRAM, 4 GB of eMMC memory and 16 MB of QSPI Flash memory
Retired
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
Printed circuit board for vapor extraction controller. AVT3215 A
Retired
No product available!
AVT kit for self-assembly of the comfortable direction indicator module. AVT1945 B
Retired
No product available!
The Arduino UNO WiFi board is based on the ATmega328 and it has an integrated ESP8266 WiFi Module. If you are starting out with Arduino, or starting with IoT, this is the board to get. A000133
Retired
No product available!
The second version of the clock synchronization signal receiver, transmitted with AM modulation (DCF77). The built-in MAS6180 system allows you to receive timing frames from a time pattern using a carrier frequency of 77.5 kHz. Thanks to this module, it is possible to create a clock with automatic date and time synchronization. The module has a ferrite antenna. modDCF77 v2
Retired
No product available!
No product available!
The board with the RP2040 microcontroller equipped with two ARM Cortex-M0 + cores operating at 133 MHz, 256 kB RAM. The board also has 16 MB of QSPI flash memory. The system can be programmed in C/C++ or microPython. SparkFun DEV-17717
Retired
No product available!
AVT kit for self-assembly of the event counter. AVT3188 B
Retired
No product available!
3-axis digital magnetometer, I2C, DFN10, Freescale, RoHS