- Out-of-Stock
New products
New products New products
zł301.74
24h
Dostępny
Available
Available
zł59.04
24h
Available
NGX Technologies mX-LPC1343-S
ID: 187860
mX-LPC1343-S
mX-LPC1343-S
mX-LPC1343-S is a CORTEX-M3 based stamp board for NGX's mbed-Xpresso Baseboard. The LPC1343 microcontroller has 32KB of internal flash and 8KB SRAM. In-System Programming (ISP) and In- Application Programming (IAP) via on-chip bootloader software.Programmable WatchDog Timer (WDT). 1 x UART,1 x I2C-bus interfaces Fast-mode Plus with a data rate of 1 Mbit/s. 1 x SSP controllers, 8-channel 10-bit ADC, USB 2.0 full-speed device controller with on-chip PHY for device,motor control PWM, Four general purpose counter/timers with a total of four capture inputs and 13 match outputs. And up to 42 general purpose I/O pins.GPIO pins can be used as edge and level sensitive interrupt sources.
Following are the salient features of the board
- Dimensions: 126x35 mm2
- Two layer PCB (FR-4 material)
- On-board Test Led
- 12MHz crystal
- On board debugger.
- No power supply required, powered through USB
187860
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Cables for evaluation boards, set of 10 pcs., blue colour
zł5.20
24h
Available quantity: 147
Available
Cables for evaluation boards, set of 10 pcs., red colour
zł5.20
24h
Available quantity: 215
Available
Cables for evaluation boards, set of 10 pcs., green colour
zł5.46
24h
Available quantity: 334
Available
Cables for evaluation boards, set of 10 pcs., yellow colour
zł5.61
24h
Available quantity: 48
Available
Cables for evaluation boards, set of 10 pcs., white colour
zł6.06
24h
Available quantity: 21
Available
Set of 40 pieces of male-female connection cables, in various colors, 17 cm long. CAB_M-F (Rainbow-40-17)
zł5.97
24h
Available quantity: 125
Available
Other products in the same category (16)
No product available!
No product available!
No product available!
Module with a 3-axis ADXL356C accelerometer with a measuring range up to ± 40g. The board is equipped with a Grove connector and communicates via the analog interface. Seeed Studio 101020638
Retired
No product available!
Detection device (eg in the wall) metal and wire with current (URZ1204)
Retired
No product available!
No product available!
10-channel generator of light effects - set for self-assembly
Retired
No product available!
The Micsig DP series differential probe is based on advanced metal shielding technology. It offers a 150 MHz frequency band and the ability to measure voltages up to 7000 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig DP7001
Retired
No product available!
No product available!
The module with the OV5647 sensor, working with all versions of the Raspberry Pi. It uses a built-in movable IR-CUT filter that is turned on and off automatically depending on the lighting conditions. ArduCAM B003507
Retired
No product available!
No product available!
Development kit for ST7FLITE3x microcontrollers
Delivery date unknown
No product available!
No product available!
Module with 6-axis IMU motion sensor that combines a 3-axis accelerometer and a 3-axis magnetometer in one system. It communicates via the I2C bus. Pimoroni PIM376
Retired
No product available!
No product available!
Dustyn Roberts
Delivery date unknown
No product available!
mX-LPC1343-S