- Out-of-Stock
TIMER SWITCH OF THE CEILING LIGHT - PRINTED PLATE
Electronics help you lazy and comfortable. The presented system allows for delayed switching off the light, e.g. in the bedroom. After switching the wall switch, the capacitor starts discharging. After a certain time (about half a minute), the light switches off. Delay allows you to take a seat in your favorite bed.
The system is assembled on a small plate with a diameter corresponding to the dimensions of a typical installation box. It is easy to assemble, it is cheap and reliable.
The device is especially recommended in the bedroom and everywhere where the light should go out with a delay
Selected parameters:
Download
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Side panel with I/O elements for Totem Mini Lab and Totem Micro Lab sets. There are buttons, potentiometers, LED diodes and a relay on the board. Totem TE-SP01-B
No product available!
Side panel with sensors for Totem Mini Lab and Totem Micro Lab sets. The board has a microphone, OLED display, DH11 humidity sensor, NTC thermistor, buzzer and a DC motor control module. Totem TE-SP02-B
No product available!
Side panel with audio elements for Totem Mini Lab and Totem Micro Lab sets. The board has an audio amplifier with a loudspeaker, a VU indicator, a function generator and a pi filter circuit. Totem TE-SP03-B
No product available!
A set for building a fighting robot controlled by a mobile application for a smartphone or tablet. Totem TRK-MT1G
No product available!
A set for the construction of two fighting robots (green and yellow) controlled by a mobile application for a smartphone or tablet. Totem TRK-MT2
No product available!
A kit for building a four-wheeled platform controlled by a mobile application. TMK-4WDU totem
No product available!
A set for building a mobile robot with a gripper controlled by a mobile application. TMK-DMNNG totem
No product available!
Kit for building a dog robot controlled by a wire with a switch. Totem TKR-DG
No product available!
Kit for building a giraffe robot controlled by a wire with a switch. Totem TKR-GRF
No product available!
Kit for building a dinosaur robot controlled by a wire with a switch. Totem TKR-TRX
No product available!
A set for building a walking robot controlled by a mobile application. Totem TKR-LSP
No product available!
The trigger module is designed for chargers PD 2.0 and PD 3.0. It is equipped with a USB type C input and output on pads. It enables powering devices with 9 V or 12 V and testing chargers. PDC005
No product available!
Development kit with RP2040 microcontroller equipped with two ARM Cortex-M0 + cores that work at 133 MHz, 264 kB RAM. The board has a QVGA camera, LCD display, IMU system and a microphone. ArduCAM B0302
No product available!
Camera module with a resolution of 13 MP equipped with an image sensor AR1335. It is equipped with a FoV 50° lens with an M12 mount. Designed for Raspberry Pi and Jetson Nano. ArduCAM B0277
No product available!
Robot controller dedicated to Totem sets. It is based on the ESP32 chip (WiFi and Bluetooth module), equipped with a DC motor and servo driver, RGB diodes and an IMU sensor. Totem TE-X4-KIT1
No product available!
Robot controller dedicated to Totem sets. It is equipped with Bluetooth communication, so it can be controlled using a smartphone. TMK-X3K totem
No product available!
TIMER SWITCH OF THE CEILING LIGHT - PRINTED PLATE