- Out-of-Stock
AVT2899 B
ID: 190367
I2C ANALYZER - A KIT FOR INDEPENDENT INSTALLATION
I2C ANALYZER - A KIT FOR INDEPENDENT INSTALLATION
Producer: AVT
The I2C bus is very popular - its advantages make it used in a variety of electronic devices (clocks, thermometers, sound and image processors, etc.) For many electronic constructors it is important to diagnose possible transmission problems efficiently. Unfortunately, the programming methods are unreliable. This problem is particularly important in prototype systems, constructed from 'zero'. That is why an external I2C analyzer is needed, which we present. The layout is quite simple and thanks to it very cheap. Built from popular components, it is possible to make even by novice electronics. The reception is carried out on the curriculum and the results are sent to the computer.
The device is especially recommended for constructors-electronics using the I2C bus
Selected parameters:
- analysis of rails with speeds of 0-600kHz (900kHz)
- input voltages <30V
- automatic detection of Start, Stop, data transmission and Ack / Nack confirmation signals
- connection with a computer via RS232
- operating mode indication - LED diodes
- power supply - 12Vdc
- dimensions of the tile 64x47mm
- in the set there is a printed circuit board, programmed layout, set of elements and documentation
- Detailed description in
Download
190367
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
A spatula for removing prints from the 3D printer table. Made of stainless steel, it is durable and handy
Retired
No product available!
A needle with a diameter of 0.4 mm, designed for cleaning the nozzle in 3D printers. It allows you to get rid of the remnants of the material after printing and to remove the filament in case of clogged nozzle
Retired
No product available!
Aluminum tensometer beam, allowing weight measurement up to 2 kilograms. It has four wires. It is used in kitchen scales and portable scales
Retired
No product available!
Educational set for building robots based on Totem construction elements. Designed for beginners, it allows you to create 7 robot structures based on the included assembly instructions. Totem TKR-RK1
Retired
No product available!
Module with 17x7 LED matrix display (119 LEDs) designed to work with the Raspberry Pi. It uses the IS31FL3731 driver and communicates via the I2C interface. Pimoroni PIM331
Retired
No product available!
Module with 17x7 LED matrix display (119 LEDs) designed to work with the Raspberry Pi. It uses the IS31FL3731 driver and communicates via the I2C interface. Pimoroni PIM332
Retired
No product available!
A pin expander designed for Raspberry Pi boards. It is equipped with a standard 40-pin output for connecting a minicomputer and five sets of 2x20-pin outputs for connecting expansion modules. Pimoroni PIM320
Retired
No product available!
A pin expander designed for Raspberry Pi boards. It is equipped with a standard 40-pin connector for connecting a minicomputer and five sets of 2x20-pin outputs for connecting expansion modules. Pimoroni PIM321
Retired
No product available!
A pin expander designed for Raspberry Pi boards. It is equipped with a standard 40-pin connector for connecting a minicomputer and five sets of 2x20-pin outputs for connecting expansion modules. Pimoroni PIM322
Retired
No product available!
A pin expander designed for Raspberry Pi boards. It is equipped with a standard 40-pin connector for connecting a minicomputer and two sets of 2x20-pin outputs for connecting expansion modules. Pimoroni PIM511
Retired
No product available!
Extension module for Raspberry Pi. The board has 7 RGB LEDs, four 14-segment displays, three single-color LEDs, as well as three touch buttons, a BMP280 sensor and a buzzer. Pimoroni PIM242
Retired
No product available!
Module with 6 5x7 LED matrix displays designed to work with the Raspberry Pi. It uses IS31FL3730 drivers and communicates via the I2C interface. Pimoroni PIM187
Retired
No product available!
Module with 6 5x7 LED matrix displays designed to work with the Raspberry Pi. It uses IS31FL3730 drivers and communicates via the I2C interface. Pimoroni PIM187
Retired
No product available!
A module with 5 buttons and an RGB diode, designed to work with the Raspberry Pi. The buttons are connected to the minicomputer through the GPIO expander controlled by the I2C interface. Pimoroni PIM301
Retired
No product available!
Kit for controlling soil moisture of cultivated plants. It contains the HAT Mini module, soil moisture sensors and pots and seeds of herbs: basil, coriander and rosemary. Pimoroni PIM518
Retired
No product available!
Kit for controlling soil moisture of cultivated plants. It contains the HAT Mini module, soil moisture sensors and pots and seeds of chilli. Pimoroni PIM519
Retired
No product available!
I2C ANALYZER - A KIT FOR INDEPENDENT INSTALLATION