- Out-of-Stock
AVT1465 B
ID: 190422
SAFE HALOGEN BULB LIGHT SWITCH - SELF INSTALLATION KIT
SAFE HALOGEN BULB LIGHT SWITCH - SELF INSTALLATION KIT
Producer: AVT
Halogen bulbs are relatively easy to destroy when switched on, because they then draw a very high current (even several times greater than the rated one). This causes the filament to burn out and the entire element has to be replaced. This situation can be avoided by using the presented set. Its operation consists in a short-term limitation of the current flowing into the halogen at the moment of its switching on. As an executive element, high power MOSFET is used. Because the system works very briefly, the power lost in the transistor is relatively small so that the element does not need a heat sink. The whole switch is assembled on a small plate and easily fits directly next to the halogen bulb holder.
The device is especially recommended for all users of halogen lighting
Selected parameters:
- for halogen lamps for 6 and 12V voltage
- maximum power of the protected 50 W bulb (depending on the elements used)
- no heat sink
- power supply - 6-12V
- dimensions of the plate 23x22mm
- in the set a printed circuit board, a set of elements and documentation
Detailed description in EP 5/08
Download
190422
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
C-Mount lens. Focal length 5 mm, FoV 60.3° (H), 47.1° (V) manual focus and adjustable aperture. Designed to work with the Raspberry Pi HQ camera. ArduCAM LN042
Retired
No product available!
Quad-band GSM/GPRS module operating at 850/900/1800/1900MHz frequencies. It has integrated TCP/IP, UDP, FTP, PPP network protocols. Quectel M95FA
Retired
No product available!
Module with 9-axis IMU BMX160 sensor (accelerometer, gyroscope and magnetomet) and BMP388 pressure/temperature sensor. Communication via the I2C interface. DFRobot SEN0252
Retired
No product available!
Minicomputer Rockchip RK3328 quad-core processor and 1GB RAM. The module has two Ethernet ports, USB 2.0 port and USB type C. It is equipped with a microSD card slot. The kit includes a CNC metal case. FriendlyELEC NanoPi R2S
Retired
No product available!
Vision Edge computing platform with ARM Cortex-A53 1.2 GHz 64-bit quad-core processor, ARM Cortex-R5 600 MHz dual-core processor, embedded Mali400 graphics processor and FPGA chip. MYIR VECP Starter Kit
Retired
No product available!
The minicomputer with the Intel Celeron J4115 quad-core processor (2.5 GHz, 64-bit) has 2 slots for DDR4 RAM modules. Additionally, it is equipped with, among others: Gigabit Ethernet, HDMI 2.0 port and Display Port 1.2 4K/60Hz, four USB sockets, 24 GPIO, PCI-e slot, two SATA3 connectors. Rev-B+. ODROID H2+
Retired
No product available!
LPCXpresso55S16 evaluation kit with LPC55S16 microcontroller with ARM Cortex-M33 core. The board contains built-in LPC-Link2, audio subsystem, accelerometer, USB interfaces and Arduino connectors. NXP LPC55S16-EVK
Retired
No product available!
The MIMXRT1062DVL6A Processor Evaluation Kit, which runs up to 600 MHz, has 256 MB of SDRAM, 512 MB of Flash and 64 QSPI Flash. NXP MIMXRT1060-EVK
Retired
No product available!
Starter kit with the Kinetis K32 L2B microcontroller, integrated with the OpenSDA programmer-debugger, LCD display, accelerometer and MEMS magnetometer and USB connector. Conclusions compatible with Arduino. NXP FRDM-K32L2B3
Retired
No product available!
Wired mouse with a precise optical sensor. It has a button to change the resolution in four levels: 800/1200/1600/2400 DPI. 1.8m cable with USB plug. Natec NMY-0667
Retired
No product available!
Kit with LS1046A Freeway development board equipped with 4-core LS1046A processor, 4 GB RAM, 4GB Flash, 4 Gigabit Ethernet connectors, 2 USB 3.0 connectors, microSD slot and two M.2 slots. NXP FRWY-LS1046A-AC
Retired
No product available!
Adapter for connecting a Raspberry Pi to the OM-SE050ARD development board. It allows you to run the EdgeLock SE050 application on a Raspberry Pi. NXP OM-SE050RPI
Retired
No product available!
LPC55S69JEV98K, ARM Cortex-M33 Microcontroller, 32 bit, 150 MHz, 640 KB Flash, VFBGA98
Retired
No product available!
USB - CAN converter module. It allows the device to be connected to a computer (USB) or microcontroller (UART) via the CAN bus. USB CAN CONVERTER (UCCB)
Retired
No product available!
Set with HQ camera, HDMI adapter, lens, tripod and Jetvariety adapter. Kit designed for NVIDIA Jetson Nano. ArduCAM B0243
Retired
No product available!
A minisumo robot on a tracked chassis with Pololu 100:1 HP motors. Fully assembled robot, additionally requires four AA batteries. Pololu 3127
Retired
No product available!
SAFE HALOGEN BULB LIGHT SWITCH - SELF INSTALLATION KIT