.png)
- Out-of-Stock
AVT955 A
ID: 190495
CLIP MINIMODUŁ - PRINTED PLATE
CLIP MINIMODUŁ - PRINTED PLATE
Producer: AVT
The presented CLIP minimodule can be treated by its constructors as a hybrid integrated circuit. It allows reading the caller's number by any electronic system. Communication between the minimodule and the system in which it is built takes place via a simple interface having the character of a bus (bus).
The caller's data, its number together with the current date and time are sent between the first and second ringing signal. They were encoded using FSK modulation. The entire CLIP package consists of three consecutive SMMR, MARK and MESSAGE blocks.
The device is especially recommended in systems using the identification of the caller's number
Selected parameters:
- module reading CLIP information
- possibility of working in two modes - with a digital interface or interface for LCD
- small dimensions, 51x30 mm tile
- power supply - 5 Vdc
- printed circuit board and documentation included
Detailed description in EP 11/06
Download
190495
Manufacturer
- AVT SPV Sp. z o.o.
- Leszczynowa 11
- 03-197 Warszawa
- Poland
- [email protected]
Responsible person
- AVT SPV Sp. z o.o.
- Leszczynowa 11
- 03-197 Warszawa
- Poland
- [email protected]
Other products in the same category (16)
Extension for Raspberry Pi; communication module with RS-485 interface (DEV-13000). Module with the possibility of mounting the DB-9 socket, the socket should be purchased separately
Retired
No product available!
FreeSoC2 board has two processors on-board: a CY8C5868LTI-LP039 and a CY8C5888AXI-LP096. The former serves as a debugger/programmer for the latter, which is the target upon which your application code will be installed. Both parts contain a Cortex-M3 processor core, 256kB of flash memory, 64kB of SRAM, and 2kB of EEPROM. DEV-13229
Retired
No product available!
32-bit microcontroller with ARM Cortex-M4 core, XMC4200 family, 256kB Flash, VQFN-48, Infineon
Retired
No product available!
No product available!
Translator of TI voltage levels, bidirectional (no signal required to control the flow direction), 8-Bit, especially recommended for use in Push-Pull and Open-Drain systems. The system has a TSSOP20 housing
Retired
No product available!
Aluminum extensometer beam, allowing measurement of weight up to 1 kilogram. It has four wires. It is used in kitchen scales and portable scales.
Retired
No product available!
Aluminum extensometer beam, allowing weight measurement up to 3 kilograms. It has four wires. It is used in kitchen scales and portable scales.
Retired
No product available!
Aluminum extensometer beam, allowing mass measurement up to 5 kilograms. It has four wires. It is used in kitchen scales and portable scales.
Retired
No product available!
A two-wire, serial extender for I2C bus, SMBus and HDMI DDC, working at 2.7 V - 5.5 V. The system has a TSSOP8 housing. PCA9507DP
Retired
No product available!
32-bit microcontroller from the STM32F7 family with ARM Cortex-M7 core, 512kB Flash memory, 320kB SRAM, I2C, SPI, UART / USART memory, USB, CAN, 1.71 ... 3.6V, 100LQFP, STM, RoHS
Retired
No product available!
The 32-bit microcontroller from the STM32F7 family with the ARM Cortex-M7 core, has 1024 kB Flash memory and 320kB SRAM memory. Supports LCD-TFT, USB OTG HS, Ethernet, CAN, UART, I2C, SPI, ADC, DAC. System in the 144-LQFP housing. STM32F746ZGT6
Retired
No product available!
The set allows introducing distance, ambient lighting and gesture analysis into the subject using the VL6180X sensor. NUCLEO-L053R8 plate in set with VL6180X expansion board. P-NUCLEO-6180X2
Retired
No product available!
Shield for STM32 Nucleo, has two MP34DT01-M digital microphones made in MEMS technology
Retired
No product available!
9-inch display with universal HDMI interface and 10-point multitouch capacitive screen
Retired
No product available!
Load Cell Amplifier is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. SEN-13230
Retired
No product available!
Shadow Chassis is a marvelously durable and modular robot platform from RobotZone. The chassis plates and mounts are cut from ABS plastic and utilize the Actobotics 0.77" and 1.50" hub patterns for sensors, controllers, power, etc. With the included “snap on” micro-controller mounts, you can attach an Arduino, Raspberry Pi, SparkFun RedBoard, or SparkFun RedBot Mainboard!
Retired
No product available!
CLIP MINIMODUŁ - PRINTED PLATE