.png)
- Out-of-Stock
AVT2897 A +
ID: 193072
AVR SOLVITOR - PRINTED PLATES AND PROGRAMMED SYSTEM
AVR SOLVITOR - PRINTED PLATES AND PROGRAMMED SYSTEM
Producer: AVT
AVR Resurektor solves one of the most annoying problems occurring during programming of AVR microcontrollers - correct programming of fuse-bits. The serial way of programming 'in the system' does not allow setting all functions in the AVR cube. It does not allow, for example, to set tip # 1 like RESET. It is true that you can set it as an I / O pin but it will block the functioning of the ISP interface. And then you must use a parallel programmer.
The system is just such a - very truncated - parallel programmer. It has only one function - restores the default fuse-bit settings. It is an ideal tool for people starting their adventure with AVR controllers.
The device is especially recommended for people programming AVR controllers
Selected parameters:
- ATiny2313 and ATmega8 support
- system without switches, jumpers, etc.
- automatic detection of the type of programmed circuit
- very simple operation - just press the RESET button
- verification after saving
- power supply - 12Vdc
- tile dimensions 87x57mm
- a printed circuit board, programmed layout and documentation in the set
- Detailed description in EdW 4/09
Download
193072
Manufacturer
- AVT SPV Sp. z o.o.
- Leszczynowa 11
- 03-197 Warszawa
- Poland
- [email protected]
Responsible person
- AVT SPV Sp. z o.o.
- Leszczynowa 11
- 03-197 Warszawa
- Poland
- [email protected]
Other products in the same category (16)
The Raspberry Pi GPIO connector adapter allows you to output signals from Raspberry Pi to the contact plate. Two LEDs indicate +3.3V and +5V power supply
Retired
No product available!
No product available!
MOD-25.Z - touch sensitive button module with monostable function. The sensor operates based on the AT42QT1011 system.
Retired
No product available!
No product available!
No product available!
The module enables connection of two devices with I2C interface working with different voltage levels. MOD-28.Z
Retired
No product available!
It is used to monitor the temperature measurement and other parameters. The expansion module has an I2C / 1-Wire converter (DS2482) through which DS18B20 temperature sensors can be connected using two or three wires. MOD-29.Z
Retired
No product available!
Power module with IRFR4105Z transistor (MOD-30.Z), maximum current 2A, 5V power supply or 5V - 12V range (selection by jumper)
Retired
No product available!
The module with the DS18B20 sensor is used to measure the temperature in the range from -55° C to + 125° C, with an accuracy of +/- 0.5° C in the range from -10° C to + 85° C. The module communicates via the 1-Wire interface, thanks to which it can be connected using 2 or 3 wires - depending on the configuration. Temperature measurement can be performed with an accuracy of 9 to 12 bits. MOD-31.Z
Retired
No product available!
Universal module with LM358 operational amplifier. Depending on the additional elements installed, the amplifier can be freely configured, eg as a reversing, non-inverting amplifier, voltage follower or an integrating amplifier. MOD-32.Z
Retired
No product available!
No product available!
The modally controlled modulation module MOD-34 / BZ allows wireless load control with a current consumption of up to 10A via a relay. Includes wireless module nRF24l01.
Retired
No product available!
No product available!
No product available!
No product available!
The module with the TXB0108 system enables the connection of systems operating with different voltage levels. It has 8-channels and is 2-way. The transmission direction of each channel is detected automatically. MOD-38.Z
Retired
No product available!
AVR SOLVITOR - PRINTED PLATES AND PROGRAMMED SYSTEM