- Out-of-Stock
CONTROLLER FOR A CAR CABIN - PLATE
A system that guarantees comfortable operation of the lamp illuminating the interior of the vehicle. After closing the door, the lighting works for a while, allowing you to sit comfortably in the armchairs. Turning the key in the ignition switch causes the bulb to be extinguished earlier. Also closing the door with the engine running immediately switches off the lighting. The blanking out of the bulb is smoothly facilitating the adaptation of the eyesight.
The system is very simple to perform and does not require complicated interference in the installation of the vehicle.
The device is especially recommended for users of cars and other vehicles
Selected parameters of the controller:
Download
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
BeagleBone AI is a minicomputer with an AM5729 processor, it has 1 GB of DDR3L RAM memory. It was created to explore issues related to artificial intelligence. BBBONE-AI
No product available!
NanoPi M4V2 is a FriendlyELEC single board computer. It uses LPDDR4 RAM memory and adds among others: POWER and RECOVERY micro switches and a microphone input.
No product available!
NanoPI NEO is a single-board chip from FriendlyELEC with a RAM of 256 MB, successfully competing with the systems created by the giant in this field Raspberry Pi. It is 25% smaller and cheaper than the Raspberry Pi Zero board with similar capabilities
No product available!
HAT for powering over Ethernet (PoE) for Raspberry Pi. It allows you to use the PoE interface to power the minicomputer via an Ethernet cable
No product available!
HAT for powering over Ethernet (PoE) for Raspberry Pi. It allows you to use the PoE interface to power the minicomputer via an Ethernet cable
No product available!
The SparkFun Qwiic Shield for Arduino Nano allows you to add the SparkFun Qwiic ecosystem to development boards that use the Arduino Nano Footprint in an easy-to-assemble shield. It connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Arduino Nano to four SparkFun Qwiic connectors.
No product available!
The SparkFun Qwiic Shield for Thing Plus provides an easy-to-assemble way to add the SparkFun Qwiic ecosystem to any development board with the Thing Plus Footprint. It connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Thing Plus to four SparkFun Qwiic connectors. Sparkfun DEV-16138
No product available!
Cytron 0.8Amp 5V-26V DC Motor Driver Shield - DC motor driver for Arduino
No product available!
No product available!
No product available!
No product available!
Cytron USB to UART Converter CH340 - USB - UART converter based on the CH340 chip
No product available!
Logic level converter (4 channels)
No product available!
The Blebox Wifi controller is dedicated to the most modern digital tapes with 5 V and 12 V, but a LED strip with WS2812 / WS2811 driver is required. BleBox pixelBox
No product available!
Evaluation kit with RISC-V Dual Core 64bit chip clocked at 400MHz. Equipped with a USB-UART converter, camera, display and Micro SD card connectors. Designed for AI applications in IoT. Seeed Studio 102991150
No product available!
Evaluation kit with RISC-V Dual Core 64bit chip clocked at 400MHz. Equipped with a USB-UART converter, OV2640 camera, LCD display. The set is enclosed in a housing. Designed for AI applications in IoT. Seeed Studio 110991191
No product available!
CONTROLLER FOR A CAR CABIN - PLATE