- Out-of-Stock
AVT5389 UK
ID: 193543
FOUR CHANNEL THERMOMETER WITH LED DISPLAY - PROGRAMMED SYSTEM
FOUR CHANNEL THERMOMETER WITH LED DISPLAY - PROGRAMMED SYSTEM
We present an electronic thermometer measuring temperature in four distant places. The measurement result is shown on a four-position, large and legible LED display. Temperature sensors DS1820 were used as temperature sensors. Connecting each of them to the thermometer requires only two wires, which makes the entire installation easy and convenient to set up, for example, at home.
The device is especially recommended for simultaneous temperature control in many places
Selected parameters:
- number of temperature sensors 1-4
- automatic (every 3 seconds) or manual switching of measuring channels
- measured temperatures in the range -55 to + 125 ° C
- presentation of results - a four-digit LED display and LED diodes indicating the active measurement path
- automatic recognition and cooperation with sensors type DS1820, DS18S20, DS18B20
- accuracy of readings 0.1stC (DS18B20) or 0.5stC (for DS1820 and DS18S20)
- the system does not require calibration
- power supply - 7-16Vdc
- programmed layout
- Detailed description in
- or
193543
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
No product available!
The miniature digital potentiometer allows you to replace the analog potentiometer and control the resistance value using two buttons. The module contains inputs of the UP / DOWN buttons (for increasing and decreasing the resistance) and outputs in accordance with the analog potentiometer A, W, B (description on the circuit board). MOD-19.Z
Retired
No product available!
Xmega eXploreGO module with ATXmega128A4U microcontroller (version without MP3). The module is equipped with in DataFlash memory, microSD card connector. MOD-20 / AZ
Retired
No product available!
MOD-21.Z - push button module with bistable operation. The sensor operates based on the AT42QT1012 system.
Retired
No product available!
The Raspberry Pi GPIO connector adapter allows you to output signals from Raspberry Pi to the contact plate. Two LEDs indicate +3.3V and +5V power supply
Retired
No product available!
No product available!
MOD-25.Z - touch sensitive button module with monostable function. The sensor operates based on the AT42QT1011 system.
Retired
No product available!
No product available!
No product available!
The module enables connection of two devices with I2C interface working with different voltage levels. MOD-28.Z
Retired
No product available!
It is used to monitor the temperature measurement and other parameters. The expansion module has an I2C / 1-Wire converter (DS2482) through which DS18B20 temperature sensors can be connected using two or three wires. MOD-29.Z
Retired
No product available!
Power module with IRFR4105Z transistor (MOD-30.Z), maximum current 2A, 5V power supply or 5V - 12V range (selection by jumper)
Retired
No product available!
The module with the DS18B20 sensor is used to measure the temperature in the range from -55° C to + 125° C, with an accuracy of +/- 0.5° C in the range from -10° C to + 85° C. The module communicates via the 1-Wire interface, thanks to which it can be connected using 2 or 3 wires - depending on the configuration. Temperature measurement can be performed with an accuracy of 9 to 12 bits. MOD-31.Z
Retired
No product available!
Universal module with LM358 operational amplifier. Depending on the additional elements installed, the amplifier can be freely configured, eg as a reversing, non-inverting amplifier, voltage follower or an integrating amplifier. MOD-32.Z
Retired
No product available!
No product available!
The modally controlled modulation module MOD-34 / BZ allows wireless load control with a current consumption of up to 10A via a relay. Includes wireless module nRF24l01.
Retired
No product available!
FOUR CHANNEL THERMOMETER WITH LED DISPLAY - PROGRAMMED SYSTEM