.png)
- Out-of-Stock
AVT2829 B
ID: 193828
UNIVERSAL AMPLIFIER CONTROLLER - KIT FOR INDEPENDENT INSTALLATION
UNIVERSAL AMPLIFIER CONTROLLER - KIT FOR INDEPENDENT INSTALLATION
Producer: AVT
Most self-made audio amplifiers have one major disadvantage - their control is only possible manually - manually. Today, in the era of remote control of everything that surrounds us, such a solution is unacceptable ;-). They can be easily eliminated by performing and installing the presented set.
It is a system that allows you to remotely control any power amplifier. Any remote control can be used for operation. The system learns the appropriate commands. After leaving the programming mode it is possible to switch the device on and off and to control its volume. The controller uses a potentiometer driven by a motor. It simplifies its installation in the audio track and makes it very versatile - the system can be installed even in tube equipment.
The device is particularly useful for electronics-electro-acoustics that construct audio systems by themselves, also in the service, when modifying existing devices
Selected parameters:
- volume control - potentiometer with motor
- full galvanic separation from the m.cz path
- remote switching on / off of the audio device
- the possibility of using any remote control
- operating mode indication - LED diodes
- layout based on software written under Bascom
- power supply - 230 Vac
- in the set a printed circuit board, a set of elements and documentation
- Detailed description in EdW 6/07
Download
193828
Manufacturer
- AVT SPV Sp. z o.o.
- Leszczynowa 11
- 03-197 Warszawa
- Poland
- [email protected]
Responsible person
- AVT SPV Sp. z o.o.
- Leszczynowa 11
- 03-197 Warszawa
- Poland
- [email protected]
Other products in the same category (16)
The Arduino 9 Axes Motion Shield allows your Arduino to measure movement: orientation, acceleration and magnetic field. A000070
Retired
No product available!
The Arduino GSM Shield connects your Arduino to the internet using the GPRS wireless network. Just plug this module onto your Arduino board, plug in a SIM card from an operator offering GPRS coverage and follow a few simple instructions. You can also make/receive voice calls (you will need an external speaker and microphone circuit) and send/receive SMS messages.
Retired
No product available!
The Arduino GSM Shield connects your Arduino to the internet using the GPRS wireless network. Just plug this module onto your Arduino board, plug in a SIM card from an operator offering GPRS coverage and follow a few simple instructions. You can also make/receive voice calls (you will need an external speaker and microphone circuit) and send/receive SMS messages.
Retired
No product available!
Plastic holder that could fit all the boards with Arduino UNO size (68,6 mm x 53,4 mm). Contains 5 pieces in different colours. A000018
Delivery date unknown
No product available!
CryptoShield is a dedicated security peripheral for the Arduino. This shield adds specialized ICs that perform various cryptographic operations which will allow you to add a hardware security layer to your Arduino project. It also is a nice device for those performing embedded security research. DEV-13183
Retired
No product available!
No product available!
Banana Pi R1 acrylic clear case. The case needs to be assembled by yourself
Retired
No product available!
The housing for the Banner PI G1 Debugger made of transparent plastic. Housing for self-assembly
Retired
No product available!
The I2C electric level conversion module is specifically designed for Banana Pi. The module converts the 3.3V of I2C electric level to 5V level or converts 5V to 3.3V
Retired
No product available!
BPI AD/DA extend module with the PCF8591 single-chip, single-supply low-power 8-bit CMOS data acquisition device with four analog inputs, one analog output and a serial I2C-bus interface
Retired
No product available!
No product available!
5dB antenna for the Banana Pi R1 router in the version with 300Mps wifi and five LAN 100/1000 ports.
Retired
No product available!
STM32F103 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
CC3200 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
CC2530 and CC2540 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
It is a standard audio-video cable, which can be successfully used to connect Banana Pi M1 or Raspberry Pi 1 model B and A. Cable length is 98 cm, has two ends of the chinch type.
Retired
No product available!
UNIVERSAL AMPLIFIER CONTROLLER - KIT FOR INDEPENDENT INSTALLATION