- Out-of-Stock
AVT1520 C
ID: 193858
REMOTE RADIO SWITCH - A SET ASSEMBLED AND STARTED
REMOTE RADIO SWITCH - A SET ASSEMBLED AND STARTED
Producer: AVT
The set consists of a transmitter and a receiver equipped with RX / TX 433 radio modules. Transmission, reception and work control are performed by two ATtiny13 microcontrollers (one in the transmitter and the other in the receiver). The transmitter in the state of rest does not take electricity - its activation causes the button to be pressed. Immediately after the start-up, the battery voltage is checked - the LED diode is too low. The receiver can work as a timer or a traditional bistable switch.
The device is particularly recommended for people who need wireless and remote control systems
Selected parameters:
- the system uses ready-made, tuned transmitter / receiver modules
- operating frequency 433MHz
- control of the voltage supplying the transmitter
- signaling of the transmitter status - a two-color LED
- receiver's executive system - relay
- the possibility of the receiver working as a time or bistable relay
- receiver status signaling - two-color LED
- power supply - 12Vdc (transmitter), 230Vac or 12dc (receiver)
- u put assembled and running (1 remote in the set)
Note: You can buy more pilots / 2 for the set
A detailed description in EP 4/09
Download
193858
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
Pre-installed Android4.4 or latest version for ODROID-XU3 and XU4. Ready to run out of box 8Gbyte eMMC Version 5.0 interface from Toshiba. JEDEC/MMCA version 5.0:HS400 interface with 8bit DDR mode
Retired
No product available!
Pre-installed XUbuntu 15.04 or latest version for ODROID-XU3, XU4 and HC1
Retired
No product available!
Pre-installed XUbuntu 15.04 or latest version for ODROID-XU3, XU4 and HC1
Retired
No product available!
The Cloudshell for XU4 is an affordable DIY Network Attached Storage (NAS) Solution to create your own personal cloud! It includes a color LCD console display on the front and has room for a 2.5inch HDD/SSD along with the XU4 board inside the CloudShell
Retired
No product available!
The Cloudshell for XU4 is an affordable DIY Network Attached Storage (NAS) Solution to create your own personal cloud! It includes a color LCD console display on the front and has room for a 2.5inch HDD/SSD along with the XU4 board inside the CloudShell
Retired
No product available!
Cooling Fan X is a cooling fan that can be used to cool any processor that works under heavy load. It can be mounted on the heat sink housing with 4 screws
Retired
No product available!
Photon Wearable Shield makes it easy to add the WiFi enabled Photon to any wearables project. Each pin on the Photon is broken out into large sewing pins. Use conductive thread to make your next wearables projects. DEV-13328
Retired
No product available!
The cable allows connecting the ATMEL-ICE programmer to the commissioning set with any connector (operated by the programmer), through individual pin connectors
Retired
No product available!
1-channel monochrome system of adding subtitles on the image (OSD - On-Screen Display) with integrated EEPROM, TSSOP28, Maxim memory
Retired
No product available!
No product available!
The controller can control two brush motors, communicating with the master system using USB Micro-B, TTL serial interface, analog signals, as well as signals from the RC apparatus. The current capacity of 5A / channel allows you to control high-power motors. Polol 2394
Retired
No product available!
EEPROM CAT93C86LI-G memory; 16kbit; 2K x 8bit; access time: 150ns; Power supply: 1.8 ... 5.5 V; 8-Pin PDIP
Retired
No product available!
Nettemp Pi Hat is a module that allows to connect eight trees of sensors with I2C/1-Wire interface and control of four relays outputs. Thanks to the extension board is possible to build in an easy way e.g. a multipunkt temperature controller.
Retired
No product available!
32GB microSDHC Memory Card with SD Adapter, class 10 A1, Kingston
Retired
No product available!
WiFi 802.11 b / g / n module with ESP8266 system, 5 leads are available with 2 mm pitch with the possibility of soldering of gold pins, power lines, reset line and UART interface have been led to the connector. 3.3V power supply
Retired
No product available!
WiFi 802.11 b / g / n module with ESP8266 system, 8 pins with 2.54 mm pitch are available with soldered gold pins, 3 GPIO lines, reset, power supply and UART interface on the connector. U.FL. Antenna Connector 3.3 V power supply
Retired
No product available!
REMOTE RADIO SWITCH - A SET ASSEMBLED AND STARTED