- Out-of-Stock
A traditional alarm clock with an alarm clock does not provide full convenience of use when the time of alarm varies on different days of the week. You must remember to change the settings each time. An additional problem is the weekend - then usually we do not wish to have any sounds disturbing sleep in the morning. The presented problem can be solved in two ways - employ someone who will control the alarm clock (;-)) or build a suitably equipped electronic timer. This is how the putty is presented. The timer uses a microprocessor. This allowed to design a versatile device with a number of unique functions. In addition to the extensive alarm clock, the display shows the current date and temperature inside the room.
The device is especially recommended for everyone who gets up early
Selected parameters:
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Cable with a length of 150 mm, on one side terminated with a Qwiic connector, and on the other side with single female goldpin connectors. It allows you to connect Qwiic modules, e.g. with development board. SparkFun CAB-14988
No product available!
Extension module for Raspberry Pi designed to build the user interface. It is equipped with a 2.4-inch TFT LCD display, microphones, speaker, buttons, joystick and RGB LEDs. SparkFun DEV-16653
No product available!
Adapter board from SODIMM200-2.5 to 2.54mm connectors
No product available!
The expansion module to support two cameras is designed for Raspberry Pi minicomputers. The board allows you to connect two cameras via CSI connectors to one minicomputer connector. ArduCAM B016601
No product available!
Evaluation kit with LittleBee GW1N-1 FPGA chip. Offers 1152 LUTs and 864 Flip-Flops (FF). The board has an FPC connector for the display and a USB type C. Sipeed Lichee Tang Nano
No product available!
Video splitter for connecting one input device to 2 receivers. Maximum 4K resolution supported. Lanberg SPV-HDMI-0002
No product available!
Video splitter for connecting one input device to 4 receivers. Maximum 4K resolution supported. Lanberg SPV-HDMI-0004
No product available!
Video splitter for connecting one input device to 8 receivers. Maximum 4K resolution supported. Lanberg SPV-HDMI-0008
No product available!
Video switch that allows you to connect 5 input devices to one HDMI receiver. The input signal can be selected using a button on the casing or the included remote control. Lanberg SWV-HDMI-0005
No product available!
A set of 8 knives, including 4 knives with broken blades and 4 special-purpose knives. Vorel 76280
No product available!
Module with an analog temperature and humidity sensor based on the SHT10 system. It is characterized by high reliability and stability with low energy consumption. It is compatible with 3.3V and 5V controllers. DFRobot DFR0066
No product available!
Module with a CCS811 air quality sensor for measuring the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via the I2C interface (Gravity connector). DFRobot SEN0318
No product available!
Module with a gesture and touch sensor. It recognizes 7 types of gestures and has 5 touch buttons. It is supplied with a voltage ranging from 3.3 V to 5 V and communicates via UART. DFRobot SEN0285
No product available!
Module with a 3-axis analog MMA7361 accelerometer. There are 3 Gravity connectors on the board (for each axis). The operating range of the sensor can be configured using a DIP switch. DFRobot DFR0143
No product available!
Module with a UV ultraviolet light sensor VEML6075. Enables measurement of the level of UVA (350-375 nm) and UVB (315-340 nm) radiation. It communicates via the I2C bus. DFRobot SEN0303
No product available!
The I2C-GPIO converter module is powered with the voltage of 5 V. It allows you to extend the number of digital pins of the Arduino-compatible board with an additional 16 IO pins. DFRobot DFR0013
No product available!