- Out-of-Stock
Pololu RC Servo Multiplexer 4 Channel (assembled)
This compact device serves as a four-channel multiplexer of hobby radio control pulses, allowing easy switching between two independent signal sources. A fifth channel selects whether the output is from the master or the slave source: a pulse width below the threshold selects the master channels, while a longer pulse width selects the slave channels. This version comes with header pins soldered in.
![]() |
The Pololu RC servo multiplexer can be used with standard hobby radio control systems and servo controllers to allow easy switching of servo control between two independent sources using a fifth channel as the output selector. This makes it ideal for applications in which you have two possible control sources and want to be able to switch between them on the fly. For example, you could connect two RC receivers to the same set of servos (or similar devices, such as RC-based motor controllers) and allow the master transmitter to decide whether the master or slave transmitter is in control, thereby setting up your own buddy-system training setup. Another possible application would involve multiplexing between an RC receiver and a servo controller, which would allow you to switch between autonomous and manual control of a set of servos.
![]() |
The pins on the multiplexer allow for easy connecting to servo cables: the column along the outside edge of the board is ground, the column in the middle is power (which must be supplied by the master), and the interior column is the signal. The pin spacing is 0.100". This multiplexer is available as an assembled version with male header pins soldered in or as a partial kit. The male headers can be used with standard servo connectors; the kit provides additional flexibility and compactness by allowing wires to be soldered directly to the board, as shown in the picture to the right. The kit version ships with three 13×1 male header strips, a 2×1 male header strip, and a blue shorting block.
The power supplied by the master should be between 2.5 and 15 V, and it must be capable of supplying the current that the servos connected to the outputs draw. The logic voltage used on the multiplexer board will be regulated to 5 V if the supply voltage is greater than 5 V; otherwise, it will be approximately equal to the supply voltage. Note that the master and slave signal voltages must not exceed this logic voltage.
Pins S1 through S4 comprise the four slave input signals and pins M1 through M4 comprise the four master input signals. Pins OUT1 through OUT4 are the multiplexed outputs, and their source is determined by the signal on the SEL pin. If the selection pulse width is below the 1.6 ms threshold, OUT1 through OUT4 output the signals on M1 through M4, respectively (i.e. the master source is output); otherwise, OUT1 through OUT4 output the signals on S1 through S4, respectively (i.e. the slave source is output). Note that there is approximately ±0.1 ms of hysteresis on the threshold, meaning that the pulse width will have to get to approximately 1.7 ms before the slave signals become the output, and once this happens, the signal will have to fall below 1.5 ms before the master signals become the output.
If the selection signal is invalid, an optional jumper across the pins labeled J1 determines the output behavior. If the jumper is left off, the output channels go low and stay low for as long as the signal on the SEL pin remains invalid. For many servos and electronic speed controls (ESCs), a constant low on the signal line will turn them off, which might be desirable if the control signals are known to be bad. If the jumper is in place, the output channels default to the master signals if the selection signal becomes invalid. The multiplexer considers a valid RC signal to have a 10 – 100 Hz pulse rate and a 0.5 – 2.5 ms pulse width.
The board has three indicator LEDs. If the outputs come from the master, only the green LED will be lit; if the outputs come from the slave, the yellow LED will be lit; if the outputs are turned off (all low) because of an invalid selector signal, the red and green LEDs will be lit.
![]() |
Micro Maestro 6-Channel USB Servo Controller (Assembled) |
![]() |
Servo Extension Cable 6" Female - Female |
![]() |
Pololu RC Switch with Digital Output |
Manufacturer
Responsible person
Vector network analyzer with two ports. It can perform measurements for frequencies from 50 kHz to 4.4 GHz. Equipped with an LCD display, it can be connected to a computer via USB. Nanovna V2 4"
No product available!
Vector network analyzer with two ports. It can perform measurements for frequencies from 50 kHz to 3 GHz. Equipped with an LCD display, it can be connected to a computer via USB. NanoV2 3.2"
No product available!
SDR (Software Defined Radio) receiver that allows you to receive signals in the frequency range from 10 kHz to 1 GHz. It is ideal for both monitoring low frequencies and receiving signals on higher bands
No product available!
Thermal imaging camera module with an MLX90640 infrared sensor and a 2.8" TFT LCD display. It offers an accuracy of 2°C and a viewing angle of 55°x35°.
No product available!
Li-Fe battery monitor that can measure voltage, current, power during charging and discharging, and watt-hours consumed and run time. The user can use a mobile application and a computer to control the measuring module. Juntek KG110F
No product available!
Development kit with STM32F407IGT6 microcontroller. Requires external programmer with SWD or JTAG interface. Waveshare Core407I
No product available!
Antenna dedicated to communication in LoRa networks in the 868 MHz frequency band. Equipped with an RP-SMA connector. SparkFun WRL-18083
No product available!
Visible spectrum emitter module that combines 9 discrete LEDs covering visible light wavelengths from 455 to 720 nm. It uses Qwiic connectors and I2C communication as well as a USB type C socket to power the module. SparkFun SPX-21316
No product available!
Switch module with a maximum voltage of 12 V and a current of 10 A based on a MOSFET transistor, controlled by a digital pin. It is equipped with a screw connection and a status LED. SparkFun SPX-19799
No product available!
Power monitor module that detects voltages up to 60 VDC and current up to 30 A. It uses the Allegro MicroSystems ACS37800 IC, which simplifies adding monitoring to power systems. SparkFun SPX-17873
No product available!
A Thing Plus development board that combines the Matter protocol and the Qwiic SparkFun ecosystem to facilitate the prototyping of IoT devices. It uses the MGM240P module from Silicon Labs, which provides secure connectivity for both 802.15.4 with Mesh (Thread) and Bluetooth® Low Energy 5.3 protocols. SparkFun DEV-20270
No product available!
WM8960 stereo codec module with driver for 1W class D speakers and headphones. It uses the I2S interface and the I2C bus to configure the system. SparkFun BOB-21250
No product available!
WM8960 stereo codec module with driver for 1W class D speakers and headphones. It uses the I2S interface and the I2C bus to configure the system. SparkFun BOB-21772
No product available!
MP3 player module controlled by I2C interface or switching inputs. It is based on a 1.4 W audio amplifier. The board has a 3.5 mm audio output and a connector for connecting a loudspeaker. Files are played from a microSD card. SparkFun DEV-19030
No product available!
A set with an adapter dedicated to the FLIR Lepton thermal imaging camera and the Lepton FS camera. It has been pre-configured to operate as a plug-and-play UVC 1.0 USB camera, it can also communicate via UART and I2C interface. SparkFun DEV-20813
No product available!
Motion detection module featuring Panasonic\'s EKM series PIR sensor. The EKM series is optimised for detecting small movements and is ideal for detecting movement in a small area around the sensor. It offers digital output in 32 zones with a detection distance of 5 m and a detection area of 90° x 90°. SparkFun SEN-22000
No product available!
Pololu RC Servo Multiplexer 4 Channel (assembled)