- Out-of-Stock
Pololu 781 - Bodhilabs VPack5.0V 2-AA Battery Holder w/ 5V Regulator
ID: 195557
Bodhilabs VPack5.0V 2-AA Battery Holder w/ 5V Regulator
Bodhilabs VPack5.0V 2-AA Battery Holder w/ 5V Regulator
This battery holder from Bodhilabs takes two AA cells and has an efficient 5V step-up regulator on the back, giving you a simple power source for your 5V circuits.
If you’re looking for an easy way to get a regulated 5 V for your electronics project, this battery holder from Bodhilabs is just what you need. It comes with a step-up DC-to-DC converter on the back that can provide up to 200 mA (typical; 500 mA max), and there is a jumper that can be removed to disconnect the batteries from the regulator and give you direct access to the battery voltage. We also sell the regulator PCB separately.
 |
| Bodhilabs VPack5.0V 2-AA battery holder with integrated 5V regulator. |
|---|
The leads coming off the regulator are terminated by a 0.100" 2-pin female connector into which you can plug standard 0.100" male header pins.
 |
| Connector on the Bodhilabs VPack5.0 regulated battery holders. |
|---|
For more information on the voltage regulator, please see the VPack PCB datasheet (95k pdf).
People often buy this product together with:
 |
Pololu 5V Boost Regulator NCP1402 |
 |
0.1" (2.54mm) Crimp Connector Housing: 1x2-Pin 25-Pack |
 |
Bodhilabs VPack5.0V 1-AA Battery Holder w/ 5V Regulator |
195557
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
The holder for 2 AA R6 double-row batteries is an ideal solution for people who need a simple and reliable way to connect AA batteries to obtain a voltage of 3 V
zł2.52
Delivery date unknown
No product available!
Holder for 2 AA R6 batteries with a flap and a switch is an ideal solution for people who need a simple and reliable way to connect AA batteries to obtain a voltage of 3 V
zł3.17
Delivery date unknown
No product available!
The 2 AA R6 battery holder is a basic but essential item for those who need a simple way to connect batteries for higher voltage. Cable length 10 cm
zł2.30
24h
Available quantity: 5
Available
Other products in the same category (16)
Banana Pi R1 acrylic clear case. The case needs to be assembled by yourself
Retired
No product available!
The housing for the Banner PI G1 Debugger made of transparent plastic. Housing for self-assembly
Retired
No product available!
The I2C electric level conversion module is specifically designed for Banana Pi. The module converts the 3.3V of I2C electric level to 5V level or converts 5V to 3.3V
Retired
No product available!
BPI AD/DA extend module with the PCF8591 single-chip, single-supply low-power 8-bit CMOS data acquisition device with four analog inputs, one analog output and a serial I2C-bus interface
Retired
No product available!
No product available!
5dB antenna for the Banana Pi R1 router in the version with 300Mps wifi and five LAN 100/1000 ports.
Retired
No product available!
STM32F103 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
CC3200 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
CC2530 and CC2540 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
It is a standard audio-video cable, which can be successfully used to connect Banana Pi M1 or Raspberry Pi 1 model B and A. Cable length is 98 cm, has two ends of the chinch type.
Retired
No product available!
COM-11964 Button a white economy grade 100mm diameter (outside diameter) dome illuminated push button comes with an LED, securing nut and a long life horizontal microswitch.
Retired
No product available!
Cobbler Plus - adapter enabling connection of GPIO Raspberry Pi A +, B + and Pi 2 lines to the contact plate (2.54 mm). The version is assembled. Adafruit 2029
Retired
No product available!
T-Cobbler Plus - adapter enabling connection of GPIO Raspberry Pi A +, B + and Pi 2 lines to the contact plate (2.54 mm). Goldpin connectors are included, for self-assembly. Adafruit 1989
Retired
No product available!
FPC tape length 250 mm, 50 lines, pitch 0.5 mm. Adafruit 1682
Retired
No product available!
μHex is the first low-power controller which is compatible with Arduino. It is very suitable for the battery power supply environment. A 210mAh CR2032 cell battery could make it work 60 days long. DFR0343
Retired
No product available!
The Leonardo ETH is a microcontroller board based on the ATmega32U4 and the new W5500 TCP/IP Embedded Ethernet Controller (datasheet).
Delivery date unknown
No product available!
Bodhilabs VPack5.0V 2-AA Battery Holder w/ 5V Regulator