- Out-of-Stock
A set of tasks from electrical metrology
ID: 179654
Brunon Szadkowski
About the book
The set of tasks is intended for students of the basic course of electrical metrology conducted on the first and second year of MA and engineering (day, evening, and extramural) studies at the Faculty of Electrical Engineering of the Silesian University of Technology in Gliwice. The textbook can also be used by students of older years specializing in metrology, as well as students of other faculties where the subject of electrical metrology is taught.
To facilitate the manual use of the manual - all tasks are presented along with solutions.
Table of Contents
TABLE OF CONTENTS
I. INTRODUCTION
II. LIST OF IMPORTANT MARKINGS
III. BASIC PRINCIPLES FOR FINAL DEVELOPMENT OF THE MEASUREMENT RESULT (T. Skubis)
IV. WORKS
1. Development of measurement results (T. Skubis)
2. Measurements of voltage and current intensity (J. Guzik)
3. Measurements of power, energy and electric charge (B. Kasperczyk)
4. Resistance measurements at direct current (T. Szadkowska)
5. Measurements of impedance and its components (T. Szadkowska)
6. Measurements of frequency and phase shift (J. Kwiczała)
7. Measurements of selected non-electrical quantities (A. Cichy, J. Leks)
8. Various tasks
V. ANNEXES
A. Some units of the SI system
B. Approximate formulas
C. Tables of selected distributions of random variables
D. Some physical constants
179654
Other products in the same category (16)
Filament from ROSA3D made of high-quality PLA pellets. Placed on a cardboard thimble, on which 1 kg of 1.75 mm diameter filament is wound. ROSA3D ReFill PLA Starter Red
Retired
No product available!
Filament from ROSA3D made of high-quality PLA pellets. Placed on a cardboard thimble, on which 1 kg of 1.75 mm diameter filament is wound. ROSA3D ReFill PLA Starter Winter White
Retired
No product available!
Filament from ROSA3D made of high-quality PLA pellets. Placed on a cardboard thimble, on which 1 kg of 1.75 mm diameter filament is wound. ROSA3D ReFill PLA Starter Yellow
Retired
No product available!
A kit for building an autonomous crawler robot based on the NVIDIA Jetson Nano B01. Waveshare JETANK AI Kit A
Retired
No product available!
USB 2.0 port isolator with support for Low Speed and Full Speed. The device has an isolation voltage rating of 3000 V. The isolator can be powered from the USB port, it is possible to connect an external power supply. USB-4620
Retired
No product available!
USB port isolator used for galvanic isolation of USB connection. It uses ADI (Analog Devices iCoupler) technology. EVC9001
Retired
No product available!
Female terminal block, 2-pin. Pitch 3.81mm. Height 7.8mm. Suitable for 15EDGRC male strips with a pitch of 3.81 mm. 2EDGKN-3.81
Retired
No product available!
Male terminal block, angled, 2-pin. Pitch 3.81mm. Height 7mm. 15EDGRC
Retired
No product available!
Male terminal block, angled, 3-pin. Pitch 3.81mm. Height 7mm. 15EDGRC
Retired
No product available!
Male terminal block, angled, 4-pin. Pitch 3.81mm. Height 7mm. 15EDGRC
Retired
No product available!
Male terminal block, angled, 5-pin. Pitch 3.81mm. Height 7mm. 15EDGRC
Retired
No product available!
Male terminal block, angled, 6-pin. Pitch 3.81mm. Height 7mm. 15EDGRC
Retired
No product available!
Male terminal block, angled, 7-pin. Pitch 3.81mm. Height 7mm. 15EDGRC
Retired
No product available!
Male terminal block, angled, 8-pin. Pitch 3.81mm. Height 7mm. 15EDGRC
Retired
No product available!
Male terminal block, angled, 9-pin. Pitch 3.81mm. Height 7mm. 15EDGRC
Retired
No product available!
Male terminal block, angled, 10-pin. Pitch 3.81mm. Height 7mm. 15EDGRC
Retired
No product available!
Brunon Szadkowski