- Out-of-Stock

These premium wires are stranded 26AWG wires with female terminals on one end and male terminals on the other end. Together with our 0.1" crimp connector housings, these wires can be used to make custom cables with 0.1" (2.54mm) connectors. The assortment of 3" (7.5 cm) wires includes five each of ten different colors.
![]() |
0.1" connector custom cable. |
---|
These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1×1 crimp connector housings on the ends. By combining these wires with our crimp connector housings, you can quickly and easily create custom cables with 0.1" (2.54mm) connectors that mate with various 0.1"-spaced connectors, including male and female headers and solderless breadboards. Just pick the housing for the correct number of pins, pick the colors and genders for your wires, and snap them into the housings (note: it’s not easy to get the wires back out, so plan carefully!). No soldering is required!
You can easily make cable harnesses or assemblies that branch from one connector on one side to multiple connectors on the other (an example of this is shown in the picture to the right); you can also cut off one pre-crimped end and solder the wires directly to components to make swapping connections easy, as shown in the motor picture below.
The wires are available in six lengths—3" (7.5 cm), 6" (15 cm), 12" (30 cm), 24" (60 cm), 36" (90 cm), and 60" (150 cm)—and in ten colors:
![]() |
0.1" connector custom motor cable. |
---|
These are the same colors as those used on resistor color codes and rainbow ribbon cable. The wire packs of different lengths include different quantities of wires. The table below shows the quantity included for a particular length-color combination:
length | monochromatic pack quantity | rainbow pack quantity |
---|---|---|
3" | – | 50 (5 of each color) |
6" | 10 | 50 (5 of each color) |
12" | 10 | 50 (5 of each color) |
24" | 5 | 50 (5 of each color) |
36" | 5 | 20 (2 of each color) |
60" | 2 | 10 (1 of each color) |
These wires can be purchased with male terminals on both ends, female terminals on both ends, or one male and one female terminals. These crimped terminals are designed for use with 0.1" (2.54 mm) male headers and female headers, solderless breadboards, and prototyping PCBs. Note that we also sell the crimp pins by themselves if you want to crimp your own wires.
![]() |
![]() |
Female crimp pin for 0.1" housings crimped onto a wire. |
---|
![]() |
Male crimp pin for 0.1" housings crimped onto a wire. |
---|
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x2-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x1-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x3-Pin 25-Pack |
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Pre-installed Android5.x or latest version. eMMC Version 5.0 interface or higher version from Samsung. JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode. The eMMC chipset is only compatible with Amlogic S905 and S805 series(ODROID-C1+ / C0 / C2)
No product available!
A miniature linear actuator that has a stroke range of up to 30 mm at a speed of 3 to 5 mm/s. It has a built-in motor and is powered by a voltage of 3 to 6 V
No product available!
No product available!
Evaluation kit with Edgeless EAI80 chip that combines ARM-Cortex M4F dual-core CPU and AI-NPU. It is equipped with SPI memory, camera and display connector, CANBUS connector and ESP8266 WiFi module. Banana Pi BPI-EAI 80
No product available!
No product available!
3-pin ARK mounting strip, 5.0 mm pitch. 103-5.0-03P-14-00A(H)
No product available!
No product available!
1.3 megapixel Digital Camera Module, for STM32F4DISCOVERY, STM, RoHS
No product available!
Camera module 8 MPx with IMX219 sensor and lens with a viewing angle of 75°. To be used as a replacement on the RPI Camera Board V2. ArduCAM B0188
No product available!
No product available!
No product available!
The Delock cable allows you to connect devices, such as a monitor with an HDMI port, to a mini DisplayPort interface. With a length of approximately 2 meters, gold-plated connectors, and support for Full-HD resolutions (up to 1920 x 1200 / 1080p), it ensures reliable audio and video signal transmission. It meets the DisplayPort 1.1a and High-Speed HDMI specifications, making it ideal for versatile multimedia applications.
No product available!
No product available!
No product available!
ROSA3D filament made of high-quality PLA-Silk granules characterized by intense color and exceptional gloss. 0.8 kg of filament with a diameter of 1.75 mm is wound on the spool. Filament ROSA3D PLA-Silk MIX-KOLOR
No product available!
No product available!