- Out-of-Stock

These premium wires are stranded 26AWG wires with female terminals on both ends. Together with our 0.1" crimp connector housings, these wires can be used to make custom cables with 0.1" (2.54mm) connectors. The assortment of 12" (30 cm) wires includes five each of ten different colors.
![]() |
0.1" connector custom cable. |
---|
These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1×1 crimp connector housings on the ends. By combining these wires with our crimp connector housings, you can quickly and easily create custom cables with 0.1" (2.54mm) connectors that mate with various 0.1"-spaced connectors, including male and female headers and solderless breadboards. Just pick the housing for the correct number of pins, pick the colors and genders for your wires, and snap them into the housings (note: it’s not easy to get the wires back out, so plan carefully!). No soldering is required!
You can easily make cable harnesses or assemblies that branch from one connector on one side to multiple connectors on the other (an example of this is shown in the picture to the right); you can also cut off one pre-crimped end and solder the wires directly to components to make swapping connections easy, as shown in the motor picture below.
The wires are available in six lengths—3" (7.5 cm), 6" (15 cm), 12" (30 cm), 24" (60 cm), 36" (90 cm), and 60" (150 cm)—and in ten colors:
![]() |
0.1" connector custom motor cable. |
---|
These are the same colors as those used on resistor color codes and rainbow ribbon cable. The wire packs of different lengths include different quantities of wires. The table below shows the quantity included for a particular length-color combination:
length | monochromatic pack quantity | rainbow pack quantity |
---|---|---|
3" | – | 50 (5 of each color) |
6" | 10 | 50 (5 of each color) |
12" | 10 | 50 (5 of each color) |
24" | 5 | 50 (5 of each color) |
36" | 5 | 20 (2 of each color) |
60" | 2 | 10 (1 of each color) |
These wires can be purchased with male terminals on both ends, female terminals on both ends, or one male and one female terminals. These crimped terminals are designed for use with 0.1" (2.54 mm) male headers and female headers, solderless breadboards, and prototyping PCBs. Note that we also sell the crimp pins by themselves if you want to crimp your own wires.
![]() |
![]() |
Female crimp pin for 0.1" housings crimped onto a wire. |
---|
![]() |
Male crimp pin for 0.1" housings crimped onto a wire. |
---|
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x2-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x3-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x4-Pin 10-Pack |
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
No product available!
No product available!
No product available!
POWER METER OF EFFECTIVE AUDIO AMPLIFIER - HARDWARE - PRINTED PLUG AND PROGRAMMED SYSTEM
No product available!
No product available!
No product available!
LCD 2x16, 65x27.7mm, STN, no backlight, enhanced temperature range, CHIP ON GLASS, HD47780 compatible controller - NT7603
No product available!
No product available!
No product available!
This transducer is about 45mm in diameter and has 4Ω impedance and should be run at about 5W
No product available!
Plastic gear motor 200:1, output shaft at 90°, operating voltage 6 V, current consumption from 0.07 A to 0.8 A, speed 51 RPM and a maximum torque of 7.2 kg*cm. Pololu 1120
No product available!
Permanent cylindrical neodymium magnet with a diameter of 8 mm and a height of 2 mm.
No product available!
Brushless motor driver module with current efficiency up to 20 A. It can work with LiPo 3S and 4S packages. BLHeli XSD20A
No product available!
No product available!
No product available!
No product available!