- Out-of-Stock
zł971.80
3pi Expansion Kit - Pololu 3pi robot expansion kit (PCB without cutouts) - red
ID: 195748
A set of spacers and connectors together with a PCB to expand the Pololu 3pi robot. Red PCB in a version without cutouts for the display and connectors. Pololu 976
Description
A set of spacers and connectors together with PCBs for the expansion of the Pololu 3pi robot. Red PCB in a version without cutouts for the display and connectors.
The expansion plate adapts to the chassis diameter of 3pi and is mounted just above the wheel tops with the four attached screws and spacers. Once assembled, the circuit board has electrical connections with the base, which allows you to connect your own electronics with a 3pi robot. These connections provide access to the ATmega168 LCD contacts, ISP programming contacts and free / shorted contacts, as well as to three voltages: VBAT (battery voltage), VCC (regulated 5 V) and VBST (regulated 9,25 V, which is supplied to the motors ). In addition, the expansion board connects to the base's power button and battery charging port, allowing you to add your own power buttons and charging ports.
This version of the kit may be better than the version with cutouts for those users who need additional I/O lines or additional space for prototyping and do not need an LCD display.
Kit contains
- PCB in red without cutouts
- 2 x Extended male connector 2x7
- 2 x Extended 1x2 male connector
- 1 x 2x7 female connector
- 2 x 1x2 female connector
- 4 x Nylon spacers 22 mm
- 4 x Screw
- 4 x Nut
195748
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Kit to expand the Pololu 3pi robot to Pololu m3pi with a mbed socket board. Includes non-soldered PCB as well as necessary connectors and components for self-assembly. Pololu 2152
zł108.28
24h
Available quantity: 1
Available
Other products in the same category (16)
Aluminum extensometer beam, allowing measurement of weight up to 1 kilogram. It has four wires. It is used in kitchen scales and portable scales.
Retired
No product available!
Aluminum extensometer beam, allowing weight measurement up to 3 kilograms. It has four wires. It is used in kitchen scales and portable scales.
Retired
No product available!
Aluminum extensometer beam, allowing mass measurement up to 5 kilograms. It has four wires. It is used in kitchen scales and portable scales.
Retired
No product available!
The set allows introducing distance, ambient lighting and gesture analysis into the subject using the VL6180X sensor. NUCLEO-L053R8 plate in set with VL6180X expansion board. P-NUCLEO-6180X2
Retired
No product available!
Shield for STM32 Nucleo, has two MP34DT01-M digital microphones made in MEMS technology
Retired
No product available!
9-inch display with universal HDMI interface and 10-point multitouch capacitive screen
Retired
No product available!
Load Cell Amplifier is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. SEN-13230
Retired
No product available!
Shadow Chassis is a marvelously durable and modular robot platform from RobotZone. The chassis plates and mounts are cut from ABS plastic and utilize the Actobotics 0.77" and 1.50" hub patterns for sensors, controllers, power, etc. With the included “snap on” micro-controller mounts, you can attach an Arduino, Raspberry Pi, SparkFun RedBoard, or SparkFun RedBot Mainboard!
Retired
No product available!
Bluetooth module for mounting in SMD technology with a fully configurable UART interface - transfer speed up to 2 Mb / s. WRL-11786
ATTENTION! A newer version of this product is available.
Click to go to the product page
Retired
No product available!
The LCD Button Shield V2 attaches to your Arduino to provide a 16x2, black character, green back light LCD with a keypad consisting of 5 keys — select, up, right, down and left. With this shield you will be able to move through menus and make selections straight from one board attached to your Arduino without requiring a massive tower of shields. DEV-13293
Retired
No product available!
Nintendo DS Screen Kit joins two of our more unique products together to provide you with an easy means to equip your next project with touchscreen functionality. Inside each kit is one Nintendo DS Touchscreen and one SparkFun Touchscreen Connector Breakout. LCD-13631
Retired
No product available!
MG2639 SparkFun Cellular Shield is a perfect addition to any Arduino project that requires connectivity when there’s no WiFi or Ethernet access nearby. The ZTE MG2639 module, which this shield is built around, supports SMS, TCP, UDP, and can even be used to make or receive phone calls. CEL-13120)
Retired
No product available!
Imagine an Arduino Shield that can be configred to be an LCD, GPS, Wuifi, or any shield you may think of!
Delivery date unknown
No product available!
Module with analogue UV light sensor ML8511. It enables the measurement of the radiation intensity for the UV-A (320-400nm) and UV-B (280-320nm) waves. Analog interface. DFRobot SEN0175
Retired
No product available!
What you need is an add on prototyping T-breakout board, which can break out all those tasty power, GPIO, I2C, ADC pins from the 40 pin header onto a solderless breadboard. This set will make "cobbling together" prototypes with the ODROID-C1 super easy
Retired
No product available!
Development Boards & Kits - ARM SAMD10 Xplained Mini evaluation kit, Microchip
Retired
No product available!
A set of spacers and connectors together with a PCB to expand the Pololu 3pi robot. Red PCB in a version without cutouts for the display and connectors. Pololu 976