- Out-of-Stock
Mini digital servo equipped with a metal gear. A standard PWM modeling signal is used for control. The servo has a range of motion of approximately 145°. The recommended operating voltage is 6 V and at this voltage the servo has a speed of 0.13 s/60° and a torque of 3.9 kg*cm. The cable is terminated with a standard JR/Futaba 3-pin connector. Perfect for small flying models.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The Pololu 779 15 cm servo extension with two female JR connectors enables easy and flexible connection of devices with 3-pin male connectors. It is used in robotics, automation, and RC systems to integrate servos, sensors, and controllers while maintaining the appropriate pitch and line designation.
No product available!
Twisted Servo Extension Cable 6" Female - Female
No product available!
16-Channel 12-bit PWM/Servo Driver - I2C interface - PCA9685, RoHS
The servo driver module is an extension intended for minicomputers Raspberry Pi Zero / Zero W / Zero WH / 2B / 3B / 3B +. Allows you to control 16 PWM channels. Waveshare 15275
No product available!
Universal tester of servos and ESC regulators. It allows you to check the operation of the servo without the need for a transmitter and receiver
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
hb03w-p-000-00
No product available!
No product available!
No product available!
Adafruit 2486 - NETduino 3 WiFi is an open source electronics platform using the .NET Micro Framework
No product available!
The Arduino M0 represents a simple, yet powerful, 32-bit extension of the Arduino UNO platform. The board is powered by Atmel’s SAMD21 MCU, featuring a 32-bit ARM Cortex® M0 core.
No product available!
Arduino Yun Mini is a breadboard PCB developed with ATmega 32u4 MCU and QCA MIPS 24K SoC CPU operating up to 400 MHz. Qualcomm Atheros CPU supports a Linux distribution based on OpenWRT named Linino. The board has built- in WiFi, supports 20 digital input/output pins, a 16 MHz crystal oscillator, a micro USB connector, an ICSP header, two reset buttons and one user button.
No product available!
The Arduino 4 Relays Shield allows your Arduino driving high power loads that cannot be controlled directly by Arduino\'s digital pins. The Shield features four relays, each relay with 2 pole changeover contacts (NO and NC). Four LEDs indicate the on/off state of each relay. (A000110)
No product available!
The Arduino Ethernet Shield 2 allows an Arduino Board to connect to the internet. It is based on the Wiznet W5500 Ethernet chip. The Wiznet W5500 provides a network (IP) stack capable of both TCP and UDP. There is an onboard micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Uno and Mega
No product available!
The Leonardo ETH is a microcontroller board based on the ATmega32U4 and the new W5500 TCP/IP Embedded Ethernet Controller (datasheet).
No product available!
The Arduino 9 Axes Motion Shield allows your Arduino to measure movement: orientation, acceleration and magnetic field. A000070
No product available!
The Arduino GSM Shield connects your Arduino to the internet using the GPRS wireless network. Just plug this module onto your Arduino board, plug in a SIM card from an operator offering GPRS coverage and follow a few simple instructions. You can also make/receive voice calls (you will need an external speaker and microphone circuit) and send/receive SMS messages.
No product available!
Mini digital servo with metal gear. It has a range of motion of 145°. Pololu 1047