- Out-of-Stock
Methane Gas Sensor MQ-4
This semiconductor gas sensor detects the presence of methane (CNG) gas at concentrations from 300 ppm to 10,000 ppm, a range suitable for detecting gas leaks. The sensor’s simple analog voltage interface requires only one analog input pin from your microcontroller.
![]() |
This methane gas sensor detects the concentration of methane gas in the air and ouputs its reading as an analog voltage. The concentration sensing range of 300 ppm to 10,000 ppm is suitable for leak detection. For example, the sensor could detect if someone left a gas stove on but not lit. The sensor can operate at temperatures from -10 to 50°C and consumes less than 150 mA at 5 V. Please read the MQ4 datasheet (161k pdf) for more information about the sensor.
![]() |
| Gas sensor with metal case bottom view. |
|---|
Connecting five volts across the heating (H) pins keeps the sensor hot enough to function correctly. Connecting five volts at either the A or B pins causes the sensor to emit an analog voltage on the other pins. A resistive load between the output pins and ground sets the sensitivity of the detector. Please note that the picture in the datasheet for the top configuration is wrong. Both configurations have the same pinout consistent with the bottom configuration.The resistive load should be calibrated for your particular application using the equations in the datasheet, but a good starting value for the resistor is 20 kΩ.
We offer two breakout boards that make it easier to interface with these sensors: a Pololu carrier board and a SparkFun carrier board. The Pololu version is shown below.
|
![]() |
Pololu MQ Gas Sensor Carrier |
![]() |
Alcohol Gas Sensor MQ-3 |
![]() |
Flammable Gas & Smoke Sensor MQ-2 |
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Shielded FTP category 5E Ethernet network cable with RJ45 plugs. Lanberg PCF5-10CC-0025-B
No product available!
Shielded FTP category 5E Ethernet network cable with RJ45 plugs. Lanberg PCF5-10CC-0025-Y
No product available!
Shielded FTP category 5E Ethernet network cable with RJ45 plugs. Lanberg PCF5-10CC-0150-O
No product available!
Shielded FTP category 5E Ethernet network cable with RJ45 plugs. Lanberg PCF5-10CC-0150-G
No product available!
Shielded FTP category 5E Ethernet network cable with RJ45 plugs. Lanberg PCF5-10CC-1000-B
No product available!
Shielded FTP category 5E Ethernet network cable with RJ45 plugs. Lanberg PCF5-10CC-0500-O
No product available!
Unshielded UTP category 5E Ethernet network cable with RJ45 plugs. Lanberg PCF5-10CC-1500-W
No product available!
Module with 4-color e-Paper display with a diagonal of 4.37" and a resolution of 512x368 px. It communicates via the SPI interface. Waveshare 4.37inch e-Paper Module (G)
No product available!
Set with SIMCom 5G SIM8202G-M2 module designed to work with the Raspberry Pi minicomputer. It supports 5G SA or NSA networks and is backward compatible with 4G and 3G networks. Waveshare SIM8202G-M2 5G HAT (B) (with case)
No product available!
Unshielded UTP category 5E Ethernet network cable with RJ45 plugs. Lanberg PCU5-10CC-0050-B
No product available!
Sound card (USB adapter) with small dimensions with two sockets for connecting a microphone and headphones. UGO UKD-1086
No product available!
Starter kit with micro:bit v2. Includes USB cable, battery basket and PVC casing. OKdo micro:bit Getting Started Kit
No product available!
Spring dedicated to the heating table of 3D printers. It allows you to adjust the degree of tightening the knob, and thus enables the proper leveling of the working table
No product available!
Spring dedicated to the heating table of 3D printers. It allows you to adjust the degree of tightening the knob, and thus enables the proper leveling of the working table
No product available!
Spring dedicated to the heating table of 3D printers. It allows you to adjust the degree of tightening the knob, and thus enables the proper leveling of the working table
No product available!
Spring dedicated to the heating table of 3D printers. It allows you to adjust the degree of tightening the knob, and thus enables the proper leveling of the working table
No product available!
Methane Gas Sensor MQ-4