- Out-of-Stock
MAX7304PMB1
ID: 198662
Maxim 16-Port IO Expander - Peripheral Module
MAX7304PMB1 Peripheral Module
Description
The MAX7304PMB1 peripheral module provides the necessary hardware to interface the MAX7304 16-port GPIO and LED driver to any system that utilizes PmodK-compatible expansion ports configurable for I2C communication. The IC features 16 GPIO ports with 12 push-pull GPIOs and four open-drain GPIOs configurable as PWM-controlled LED drivers. The device supports a 1.62V to 3.6V separate power supply for level translation. Each GPIO can be programmed to one of the two externally applied logic voltage levels. PORT12–PORT15 can also be configured as LED drivers that feature constant-current sinks and PWM intensity control with the internal oscillator. The maximum constantcurrent level for each open-drain LED port is 20mA. The intensity of the LED on each open-drain port can be individually adjusted through a 256-step PWM control. The port also features LED fading.
Refer to the MAX7304 IC data sheet for detailed information regarding operation of the IC.
Features
- Four LED Driver Pins on PORT12–PORT15
- 256-Step PWM Individual LED Intensity-Control Accuracy
- Individual LED Blink Rates and Common LED Fade-In/Out Rates
- Individually Programmable GPIOs to Two Logic Levels
- 8-Channel Individual Programmable Level Translators
- Configurable Edge-Triggered Port Interrupt
- Jumper-Selectable I2C Address Setting
- 6-Pin Pmod-Compatible Connector (I2C)
- Secondary Header Allows Daisy-Chaining of Additional Modules on I2C Bus
- Example Software Written in C for Portability
- RoHS Compliant
- Proven PCB Layout
- Fully Assembled and Tested
198662
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
No product available!
The general-purpose programmable board based on Atmel’s ATmega32U4 AVR microcontroller and arranged in the common Arduino form factor exemplified by the Uno R3 and Leonardo. Pololu 3108
Retired
No product available!
The Pololu A-Star 32U4 Prime is a general-purpose programmable board based on Atmel’s ATmega32U4 AVR microcontroller and arranged in the common Arduino form factor exemplified by the Uno R3 and Leonardo. Pololu 3109
Retired
No product available!
This version has a 56:1 metal gearbox with a 0.276"-long, 4 mm-diameter D-shaped output shaft. Key specs at 6 V: 250 RPM and 250 mA free-run, 45 oz-in (3.3 kg-cm) and 3.3 A stall. Pololu 1450
Retired
No product available!
This gearmotor consists of a high-power, 6 V brushed DC motor combined with a 4.4:1 metal spur gearbox, and it has an integrated 48 CPR quadrature encoder on the motor shaft, which provides 211.2 counts per revolution of the gearbox’s output shaft.
Retired
No product available!
The UM7 orientation sensor from CH Robotics is an Attitude and Heading Reference System (AHRS) that contains a three-axis accelerometer, rate gyro, and magnetometer. It combines this data using an Extended Kalman Filter to produce attitude and heading estimates. Pololu - 2741
Retired
No product available!
The A-Star 32U4 Mini SV is a programmable module based on the ATmega32U4 from Atmel. Unlike competing products, it has an onboard switching step-down regulator that allows it to be powered efficiently from a 5 V to 36 V supply. Pololu 3104
Retired
No product available!
This synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 5 V with an available output current of around 6 A.
Retired
No product available!
High performance full NFC compliant expansion board compatible with Raspberry Pi. EXPLORE-NFC
Retired
No product available!
SATA line for Banana Pi only. Connects a 2.5 inch Hard Disk to your Banana Pi Computer
Retired
No product available!
No product available!
This is an aluminum heat-sink for the Banana Pi RAM Chips. Run cool RAM chips with this little add-on. Just one heat-sink is needed to cover both RAM chips, use the picture below as reference. Signs of RAM or CPU overheating are computer stops responding, frozen screen and power shutt down or cycling.
Retired
No product available!
The Serial Port module is specifically designed for Banana Pi with the module use Maxim MAX232 chip and DB9 port
Retired
No product available!
Digilent ZYBO SoC platform powered by Xilinx Zynq Z-7010 with a dual-core ARM® Cortex-A9 processor and an Xilinx 7-series FPGA. 410-279
Retired
No product available!
NI LabVIEW is a graphical programming platform used by millions of engineers and scientists for problem solving, data acquisition and analysis, instrument control, automated testing and validation, prototyping, and more. 6002-549-000
Retired
No product available!
Arduino M0 PRO (M0+ Atmel processor) with build in companion chip to let you debug your application
Retired
No product available!
Maxim 16-Port IO Expander - Peripheral Module