- Out-of-Stock
Monster Moto Shield
ID: 201043
DEV-10182 - Monster Moto Shield
DEV-10182 - Monster Moto Shield
Description:
This is essentially a ramped up version of our Ardumoto motor driver shield. For this monster shield weve replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. Weve also beefed up the support circuitry so this board is capable of driving a pair of high-current motors! The VIN and motor out are pitched for our 5mm screw terminals (not included), making it easy to connect larger gauge wires.
Note: When using this board in extreme high-demand applications it may be necessary to improve thermal performance with a heat-sink or fan and to solder the wires directly to the board instead of using a screw terminal (in addition to the myriad other complications present in a high-current system) However, when using the board at currents up to 6A the chips will barely become noticeably warm.
Features:
- Voltage max: 16V
- Maximum current rating: 30 A
- Practical Continuous Current: 14 A
- Current sensing available to Arduino analog pin
- MOSFET on-resistance: 19 mΩ (per leg)
- Maximum PWM frequency: 20 kHz
- Thermal Shutdown
- Undervoltage and Overvoltage shutdown
Documents:
- Schematic
- Eagle Files
- Datasheet (VNH2SP30)
- Example Code
201043
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
Silicone protective case for the Huskylens vision module. It was made of a soft and flexible material, it perfectly fits the shape of the tile. DFRobot FIT0647
Retired
No product available!
Module with a CCS811 air quality sensor for measuring the concentration of carbon dioxide (CO2) and volatile organic compounds (VOC) in the air. It communicates via the I2C interface. DFRobot SEN0339
Retired
No product available!
Evaluation kit with SiFive Freedom E310 microcontroller with RISC-V (ISA) architecture. It includes 32MB QSPI flash memory, NXP K22 ARM Cortex-M4 microcontroller for USB support and JTAG interface, Qwiic and USB Type-C connector. SparkFun DEV-15594
Retired
No product available!
Cable with a length of 150 mm, on one side terminated with a Qwiic connector, and on the other side with single female goldpin connectors. It allows you to connect Qwiic modules, e.g. with development board. SparkFun CAB-14988
Retired
No product available!
Extension module for Raspberry Pi designed to build the user interface. It is equipped with a 2.4-inch TFT LCD display, microphones, speaker, buttons, joystick and RGB LEDs. SparkFun DEV-16653
Retired
No product available!
Adapter board from SODIMM200-2.5 to 2.54mm connectors
Retired
No product available!
The expansion module to support two cameras is designed for Raspberry Pi minicomputers. The board allows you to connect two cameras via CSI connectors to one minicomputer connector. ArduCAM B016601
Retired
No product available!
Evaluation kit with LittleBee GW1N-1 FPGA chip. Offers 1152 LUTs and 864 Flip-Flops (FF). The board has an FPC connector for the display and a USB type C. Sipeed Lichee Tang Nano
Retired
No product available!
Video splitter for connecting one input device to 2 receivers. Maximum 4K resolution supported. Lanberg SPV-HDMI-0002
Retired
No product available!
Video splitter for connecting one input device to 4 receivers. Maximum 4K resolution supported. Lanberg SPV-HDMI-0004
Retired
No product available!
Video splitter for connecting one input device to 8 receivers. Maximum 4K resolution supported. Lanberg SPV-HDMI-0008
Retired
No product available!
Video switch that allows you to connect 5 input devices to one HDMI receiver. The input signal can be selected using a button on the casing or the included remote control. Lanberg SWV-HDMI-0005
Retired
No product available!
A set of 8 knives, including 4 knives with broken blades and 4 special-purpose knives. Vorel 76280
Retired
No product available!
Module with an analog temperature and humidity sensor based on the SHT10 system. It is characterized by high reliability and stability with low energy consumption. It is compatible with 3.3V and 5V controllers. DFRobot DFR0066
Retired
No product available!
Module with a CCS811 air quality sensor for measuring the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via the I2C interface (Gravity connector). DFRobot SEN0318
Retired
No product available!
Module with a gesture and touch sensor. It recognizes 7 types of gestures and has 5 touch buttons. It is supplied with a voltage ranging from 3.3 V to 5 V and communicates via UART. DFRobot SEN0285
Retired
No product available!
DEV-10182 - Monster Moto Shield