- Out-of-Stock
Description: This high discharge LiPo is a great way to power any R/C, robotic, or portable project. This is an excellent choice for anything that requires a small battery with a lot of punch. The voltage is low enough not to tax your regulating circuits, and the discharge rate is high enough to accommodate a lot of electronics and a few small motors.
The battery has three cells and outputs 11.1V storing 1500mAh of charge. Because this is a triple cell battery pack, a special charger is needed. This battery is not compatible with single cell chargers. A compatible charger is listed below.
Note: Due to shipping restrictions, only two batteries can be shipped together at one time. We should be able to ship more than two batteries at a time by the end of 2014.
Note: Care should be taken not to short circuit or overtax these batteries because they don’t have any built-in protection circuit.
Features:
Dimensions: 71.6mm x 34.5mm x 22mm
Weight: 114g (4oz)
Documents:
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Antenna with built-in LNA amplifier with high sensitivity, for mounting in a device using a GPS module. The antenna has a 25mm cable, terminated with a U.FL plug (IPEX). Dimensions of the device: 9 x 9 x 4mm
No product available!
The GY-GPS6MV1 module is a board containing the U-blox NEO-6M GPS receiver system. The tile also includes RTC backup battery, antenna connector (U.FL), voltage stabilizer and UART signal outputs
No product available!
Kit: MAXimator, MAXimator Expander, ZL32PRG - USB Blaster PRO
No product available!
Power Supply 2.5A 5.1V for Raspberry Pi 3 model B - STONTRONICS T5875DV
No product available!
MYD-JA5D44 Development Board is a complete educational platform. Its heart is the MYIR MYC-JA5D44 module, which was equipped with the Atmel SAMA5D44 processor based on Cortex-A5 cores. The processor can work at a maximum frequency of 600 MHz. Min. RS232, RS485 connectors, HDMI connector, 3.5 mm Jack Audio inputs, microSD memory card slot, 10/100 Mbps Ethernet slot and many more.
No product available!
The Raspberry Pi GPIO Triple Expansion Board converts the single GPIO headers on your Raspberry Pi into three parts. DFR0385
No product available!
Flex Cable for Raspberry Pi Camera - 300mm / 12". Adafruit 1648
No product available!
Comes with a 6"x6" (152mm x 152mm) square of Pyralux. It\'s ED-Y type copper at 35um (1 oz/ft2) and has a polymide of 25um (1 mil). The thick copper layer means it can carry a lot of current, and its trivial to solder to it. Adafruit 1894
No product available!
Patchcord UTP 5E Ethernet cable with a length of 50 cm - gray, with 2xRJ45 connectors
No product available!
Patchcord UTP 5E Ethernet cable with a length of 50 cm - blue, with 2xRJ45 connectors
No product available!
Patchcord UTP 5E Ethernet cable with a length of 1.5 m - black, with 2xRJ45 connectors
No product available!
Patchcord UTP 5E Ethernet cable with a length of 3 m - black, with 2xRJ45 connectors
No product available!
Patchcord UTP 5E Ethernet cable with a length of 5 m - blue, with 2xRJ45 connectors
No product available!
Patchcord UTP 5E Ethernet cable with a length of 5 m - gray, with 2xRJ45 connectors
No product available!
The board gives the possibility to significantly extend the functionality of the STM32F407G-DISC1 development kit. The plate contains, among others memory card slot (microSD), Ethernet socket and connectors that can be used to attach SMT32F4DIS modules to the board
No product available!
Camera board for the STM32F407G-DISC1 set. It allows you to capture an image with a resolution of 1280 x 1024 pixels (1.3MP). The set includes a flexible cable that allows the camera to be connected to the STM32F4DIS-BB expansion board
No product available!
PRT-10470