- Out-of-Stock
Stepper motor controller for CNC milling machine - AVT5358 / 1 A set (printed circuit board)
ID: 208608
PCB for stepper motor controller CNC milling machine built using Toshiba specialized integrated circuit TA8435. The product includes a non-soldered printed circuit. AVT AVT5358 / 1 A
Description
PCB for stepper motor controller CNC milling machine built using Toshiba specialized integrated circuit TA8435. Allows you to control the stepper motor in full step 1 mode and in the so-called micro step mode 1/2, 1/4 and 1/8 of the basic engine step. Permissible continuous load current is 1.5 A per phase. The milling machine controller communicates with the computer via the LPT port and is supervised by the Mach3 software. CNC milling machine will be used in the workshop of every modeler and DIY enthusiast, it can be an interesting addition to the electronics workshop or electronic service.
Attention!
The product includes a non-soldered printed circuit.
properties
- Power supply: 24 VDC
- Power supply of the digital part: 5 VDC
- Continuous output current: 1.5 A
- Momentary output current: 2.5 A
- Motor step division: 1/1, 1/2, 1/4 and 1/8
- PCB dimensions: 68 x 48 mm
Included
- Printed circuit board
- Documentation
208608
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
You might also like
CNC stepper motor controller module built using Toshiba's specialized TA8435 integrated circuit. The product includes an assembled and tested system. AVT AVT5358 / 1 C
zł196.80
24h
Available quantity: 1
Available
Available
Available
CNC DRILLING MACHINE - POWER SUPPLY - SELF-MOUNTING KIT
zł56.63
24h
Available quantity: 1
Available
Other products in the same category (16)
Soldering station 5in1: hotair 100..480 degrees C, soldering tip 75W, power supply 0..15V / 1A, RF signal tester, voltage meter. Included, among others set of nozzles and wires for the power supply
Retired
No product available!
No product available!
No product available!
Laboratory power supply KORAD KA3005P 0-30V 5A communication with PC memory 5 power profiles
Retired
No product available!
This compact, inexpensive plastic gearmotor (high-power brushed DC motor with a 120:1 reduction gearbox) is well suited for use in small robots. While intended for operation at 4.5 V, it should run comfortably in the 3 V to 6 V range.
Retired
No product available!
Digital Proximity, Ambient Light, RGB and Gesture Sensor, Avago Technologies, RoHS
Retired
No product available!
Integrated analogue base station RFID (front-end) of the company EM Microelectronic with a frequency of 13.56MHz. The system has a SOP20 housing
Retired
No product available!
Computer fan housing Raspberry Pi 3, Raspberry Pi 2 model B and Raspberry Pi 1 model B + in dark blue plastic color
Retired
No product available!
Case for the Raspberry PI 2 model B, Raspberry PI 1 model B+ and Raspberry PI 3 computers, manufactured from high quality acrylic. CLEAR
Retired
No product available!
No product available!
No product available!
No product available!
Infrared sensor that allows measurement of distances up to 15cm, has a built-in infrared illuminator, IR receiver and a perimeter of the received signal
Retired
No product available!
Miniature (22x13.5x6mm) WiFi module b / g / n with TCP and UDP protocols operating in standalone and access point modes. 2.0mm goldpin connector. The module is equipped with a UART interface, it is also possible to control GPIO lines (also as PWM). Powered by 3.3V. Antenna: copper wire
Retired
No product available!
Ultra miniature WiFi b/g/n module, equipped with UART, SPI, PWM and GPIO interfaces. The ability to work as an access point and in standalone mode. 3.3V power supply.HF-LPT200-1
Retired
No product available!
This transducer is about 45mm in diameter and has 4Ω impedance and should be run at about 5W
Retired
No product available!
PCB for stepper motor controller CNC milling machine built using Toshiba specialized integrated circuit TA8435. The product includes a non-soldered printed circuit. AVT AVT5358 / 1 A