- Out-of-Stock
DC Motor Driver 2×15A - Lite
ID: 234539
(DRI0018)
DC Motor Driver 2×15A - Lite (DRI0018)
This DC Motor Driver can be used in 4WD mobile robot platforms, combat robots, smart car competition, drive pumps, electric fans, conveyors, etc... This module uses 4 high-performance & high-current driver chips (BTS7960) with the following protective functions: Current short, over temperature and over voltage . You can control 2 motors with only 4 digital IO at the same time. Dual 15A@13.8V max output current, good responsiveness & braking performance. Four indicator leds are provided for easy and convenient debugging without motors. There are two AL Heat Sinks in the back of the module, to provide cooling for prolonged high-power working state. This DC Motor Driver module is directly compatible with Arduino.
Applications:
- DC motor driver
- 4WD high-power mobile robot platform
- Combat robots
- Pumps
- Electric fans
- Conveyors
Specification:
- Input Voltage: 4.8 ~ 35V
- Maximum output current: 15A @ 13.8V per channel
- Peak output current: 20A @ 13.8V per channel
- PWM capability: up to 25 kHz
- Interfaces: 4 digital IO (2 PWM output include)
- Driving mode: Dual high-power H-bridge driver
- Other specifications
- Galvanic isolation to protect the microcontroller
- Dual current detection diagnostic functions
- Short circuit, overheating, over-voltage protection
- Size: 73 x 68 x 14mm
Documents:
234539
Data sheet
- Output current
- 15 A
- Number of channels
- 2
- Supply voltage min
- 4,8 V
- Supply voltages max
- 35 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
The high power motor driver module works on the basis of Infineon BTS7960B systems. Maximum controller current: 43 A, operating voltage range: 5.5V - 27V. The module has a heat sink and can be controlled from the Arduino, Raspberry Pi, and STM levels. IBT_2
zł39.96
Delivery date unknown
No product available!
Other products in the same category (16)
No product available!
Crimping tool HT106L by Prosonic, supports connectors: F59, F11, F6, UHF58, HF8
Retired
No product available!
Crimping tool LY2070B for PROSONIC 4p4c, 6p6c connectors
Retired
No product available!
BeagleBone Blue features an Octavo Systems OSD3358 System-in-Package which incorporates a Texas Instruments AM335x Sitara™ Processor, TPS65217C Power Management IC, TL5209 LDO Voltage Regulator, a DDR3 SDRAM, and over 140 passive components. BBONE-BLUE
Retired
No product available!
Pmod DPG1 is a module with a differential pressure sensor, based on the NXP MP3V5010DP system. The PCB also includes an analogue-digital ADCS7476 converter from Texas Instrument. The module allows to detect the pressure difference between two ports. The SPI interface is used for communication with the module. Digilent 410-333
Retired
No product available!
NanoPi NEO is a miniature board with the all-in-one SoC Allwinner H3 chip (ARM Cortex-A7) with built-in Ethernet communication. Works with Ubuntu MATE, Debian, etc. It can be powered by the microUSB port. The board also contains a USB port, a serial port and a 36-pin GPIO connector
Retired
No product available!
NanoPi NEO is a miniature board with the all-in-one SoC Allwinner H3 chip (ARM Cortex-A7) with built-in Ethernet communication. Works with Ubuntu MATE, Debian, etc. It can be powered by the microUSB port. The board also contains a USB port, a serial port and a 36-pin GPIO connector.
Retired
No product available!
NanoPi NEO Air is a miniature board with the SoC Allwinner H3 quad-core system (ARM Cortex-A7) with built-in WiFi and Bluetooth communication. It works with Ubuntu MATE, Debian etc. It can be powered by a microUSB port
Retired
No product available!
NanoPi A64 single board computer (SoC) with A64 Allwinned processor, SoC (ARM Cortex A-53) and dedicated FriendlyCore-Xential and UbuntuMATE operating systems
Retired
No product available!
Minicomputer with a quad-core processor (up to 1.4GHz) and 1 GB of DDR3 RAM, 8 GB of eMMC Flash memory. It has a WiFi 2.4G module and video interfaces in the form of HDMI, as well as USB2.0, MicroSD, Ethernet port and 3.5mm audio socket. FriendlyELEC NanoPC T2
Retired
No product available!
Minicomputer with an octa-core processor (up to 1.4GHz) and 2 GB of DDR3 RAM memory, 8 GB of eMMC Flash memory. It has a WiFi 2.4G module and video interfaces in the form of HDMI, as well as USB2.0, MicroSD, Ethernet port and 3.5mm audio socket. FriendlyELEC NanoPC T3
Retired
No product available!
No product available!
Orange Pi 2G-IoT is a minicomputer with a powerful ARM Cortex-A5 processor. The computer is equipped with a GSM / GPRS (2G) module, 256 MB LPDDR2 RAM, a WiFi module and a CSI camera connector, USB Host, OTG, 26 GPIO and a microSD card slot. Works with Android, Ubuntu and Debian systems
Retired
No product available!
Orange Pi Prime Development Board H5 Quad-core 2GB DDR3 SDRAM Mini PC
Retired
No product available!
Orange Pi Win 1GB DDR3 RAM A64 Quad-core 64-Bit WiFi Mini PC
Retired
No product available!
Orange Pi Win Plus A64 Quad-core 2GB WIFI Development Board
Retired
No product available!
(DRI0018)