- Out-of-Stock
AVT518 B
ID: 46185
PR89AT - MICROCONTROLER PROGRAMMER
PR89AT - MICROCONTROLER PROGRAMMER
Producer: AVT
The programmer is characterized by simplicity of execution, low cost, large possibilities. The control program works in a Windows environment. Communication with a computer is possible via the RS232 serial interface. The device can be powered directly from the computer port. The programmer is used for programming circuits in DIP40 and DIP20 enclosures.
The device was designed and made based on the AT89C51 microcontroller. It provides setting of appropriate addresses, data and levels of voltages and control signals. Communication with the computer is possible with the maximum speed of the UART unit. When writing to the Flash memory, the programmer immediately verifies whether the process has run correctly.
Recommendation:
The device is recommended for users and designers of microprocessor systems, on the website and in the electronic laboratory
Selected parameters:
- programming of circuits in DIP40 enclosures (eg 89C51, 89C52) and DIP20
- programming of 5 V and 12 V varieties (built-in inverter)
- communication through the serial port - speed 115200 b / s
- RESET button
- possibility of powering directly from the computer
- power supply - 12 V
46185
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
Adapter board from SODIMM200-2.5 to 2.54mm connectors
Retired
No product available!
Evaluation kit with Bluetooth 5.0 Sparkfun Artemis module. Equipped with a microphone, kmaers and accelerometer. Himax HM01B0 camera included. SparkFun KIT-17071
Retired
No product available!
The expansion module to support two cameras is designed for Raspberry Pi minicomputers. The board allows you to connect two cameras via CSI connectors to one minicomputer connector. ArduCAM B016601
Retired
No product available!
Evaluation kit with LittleBee GW1N-1 FPGA chip. Offers 1152 LUTs and 864 Flip-Flops (FF). The board has an FPC connector for the display and a USB type C. Sipeed Lichee Tang Nano
Retired
No product available!
Video splitter for connecting one input device to 2 receivers. Maximum 4K resolution supported. Lanberg SPV-HDMI-0002
Retired
No product available!
Video splitter for connecting one input device to 4 receivers. Maximum 4K resolution supported. Lanberg SPV-HDMI-0004
Retired
No product available!
Video splitter for connecting one input device to 8 receivers. Maximum 4K resolution supported. Lanberg SPV-HDMI-0008
Retired
No product available!
Video switch that allows you to connect 5 input devices to one HDMI receiver. The input signal can be selected using a button on the casing or the included remote control. Lanberg SWV-HDMI-0005
Retired
No product available!
A set of 8 knives, including 4 knives with broken blades and 4 special-purpose knives. Vorel 76280
Retired
No product available!
Module with an analog temperature and humidity sensor based on the SHT10 system. It is characterized by high reliability and stability with low energy consumption. It is compatible with 3.3V and 5V controllers. DFRobot DFR0066
Retired
No product available!
Module with a CCS811 air quality sensor for measuring the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via the I2C interface (Gravity connector). DFRobot SEN0318
Retired
No product available!
Module with a gesture and touch sensor. It recognizes 7 types of gestures and has 5 touch buttons. It is supplied with a voltage ranging from 3.3 V to 5 V and communicates via UART. DFRobot SEN0285
Retired
No product available!
Module with a 3-axis analog MMA7361 accelerometer. There are 3 Gravity connectors on the board (for each axis). The operating range of the sensor can be configured using a DIP switch. DFRobot DFR0143
Retired
No product available!
Module with a UV ultraviolet light sensor VEML6075. Enables measurement of the level of UVA (350-375 nm) and UVB (315-340 nm) radiation. It communicates via the I2C bus. DFRobot SEN0303
Retired
No product available!
The I2C-GPIO converter module is powered with the voltage of 5 V. It allows you to extend the number of digital pins of the Arduino-compatible board with an additional 16 IO pins. DFRobot DFR0013
Retired
No product available!
KAmodRPI RS485 CAN HAT is a shield for the Raspberry Pi computer that extends its interfaces with RS485 and CAN. Bus signals are led out to goldpin connectors and terminal blocks.
Retired
No product available!
PR89AT - MICROCONTROLER PROGRAMMER