- Out-of-Stock
zł10,639.61
.png)
New products
New products New products
AVT2499 B
ID: 46221
AMPLIFIER 4X40 W - SELF-ASSEMBLY KIT
AMPLIFIER 4X40 W - SELF-ASSEMBLY KIT
Producer: AVT
Four-channel audio amplifier with a maximum output power of 160 W (4x40 W). The set uses a TDA8571 integrated circuit from Philips. This block has a number of circuits protecting the amplifier from damage. These are circuits protecting against the effects of short circuit, overheating, electric charges and reverse connection of power supply. In addition, diagnostic circuits were made in the structure - the appearance of a low state at the appropriate end indicates the existence of a problem or a temporary overdrive.
The MODE input allows you to enter the system into STANDBY mode. Amplifier current consumption then drops to the level (type) 1 uA.
The amplifier is mounted on a small printed circuit board. A small number of elements makes it a convenient module for complex audio devices.
The device is especially recommended for all building audio equipment, both stationary and for motor vehicles
Selected parameters of the amplifier:
- number of channels - 4
- channel separation - type 50 dB
- output power - 40 W / channel (typical, for rectangular waveform)
- frequency response - 20 Hz - 20 kHz
- nonlinear distortions - type 0.1%
- loss power - max. 60 W
- quiescent current - type 200 mA
- power supply - 16-18 V (typical 14.4 V)
- in the set a printed circuit board, a set of elements and documentation
- Detailed description in
Download
46221
Manufacturer
- AVT SPV Sp. z o.o.
- Leszczynowa 11
- 03-197 Warszawa
- Poland
- [email protected]
Responsible person
- AVT SPV Sp. z o.o.
- Leszczynowa 11
- 03-197 Warszawa
- Poland
- [email protected]
Other products in the same category (16)
AVT kit for self-assembly of the GSM controller. AVT5555 B
Retired
No product available!
No product available!
Transparent housing for Orange Pi Plus 2e, folded into snaps, made of plastic. It protects and protects your computer against dust and mechanical damage
Retired
No product available!
Step Down MP2144GJ pulse converter; 2,5-5,5V; 2A; 1,2MHz; TSOT23-8; Microchip, RoHS
Retired
No product available!
No product available!
No product available!
No product available!
Assembled 4-channel dimmer for network lighting. AVT5361 C
Retired
No product available!
No product available!
Housing for Raspberry Pi 3/2 / B + two-colored (black-transparent). Mounted on screws without the use of glue, made of plastic
Retired
No product available!
Double transparent housing for Raspberry computers: Pi 3 model B +, Pi 3 model B, Pi 2 model B and Pi 1 model B + allows you to place two Raspberry Pi computers. Mounted on screws without the use of glue, made of plastic
Retired
No product available!
Bluetooth module with integrated HC-08 system. Thanks to the angular pin connector with the bus signals, it is possible to easily connect the module to the contact plate or wires
Retired
No product available!
Arduino-powered, electromyography (EMG) sensor kit that provides you with a MyoWare Muscle Sensor, each shield developed here at SparkFun, and everything you need to connect them all together. KIT-13772
Retired
No product available!
Assembled automatic power switch for car installation. AVT1877 C
Retired
No product available!
320x240, 3.2 inch Multicolor Graphic LCD, with touch screen and stand-alone controllers
Retired
No product available!
The Digilent Cmod A7 is a small, breadboard friendly 48-pin DIP form factor board built around a Xilinx Artix-7 FPGA. The board also includes a USB-JTAG programming circuit, USB-UART bridge, clock source, Pmod host connector, SRAM, Quad-SPI Flash, and basic I/O devices. 410-328
Retired
No product available!
AMPLIFIER 4X40 W - SELF-ASSEMBLY KIT