- Out-of-Stock
New products
New products New products
zł343.01
24h
Available
Available
Available
Available
Available
The world of 3D printing. Guide
ID: 536718
Anna Kaziunas France
Original title: Make: 3D Printing: The Essential Guide to 3D Printers
Translation: Zbigniew Waśko
ISBN: 978-83-246-9114-2, 9788324691142
Release date: 2014-08-25
Format: 170x230
Pages: 210
About the book
A compendium of knowledge about 3D printing!
Until recently, 3D printers could only be found in ... science fiction books. It took just a few years for these devices to become public. They open up a lot of new possibilities for designers, and the preparation of prototypes has never been so easy and fast. Reach for this book and explore the world of 3D printing!
During the reading you will learn the structure of the 3D printer and its components. Then you will become familiar with popular programs that allow you to prepare a printout. Even if you are just about to do your first 3D project, with this guide you will go through the whole process without any problems and print the prototype on your printer or in a company providing such services. You will also learn everything about 3D scanning - combining the capabilities of a 3D printer and three-dimensional scanning techniques allows you to create amazing designs! At the end, you will master issues related to the industrial use of printers, available materials and development perspectives of this field of design. Reach for this book and follow the technological spirit of the time!
Thanks to this book:
- You will get to know the structure of a 3D printer
- you will prepare your first project for 3D printing
- You will learn popular tools
- you will become familiar with the available materials
- You will get to know the development perspectives of 3D printing
Guide to the world of 3D printers!
536718
Other products in the same category (16)
Banana Pi R1 acrylic clear case. The case needs to be assembled by yourself
Retired
No product available!
The housing for the Banner PI G1 Debugger made of transparent plastic. Housing for self-assembly
Retired
No product available!
The I2C electric level conversion module is specifically designed for Banana Pi. The module converts the 3.3V of I2C electric level to 5V level or converts 5V to 3.3V
Retired
No product available!
BPI AD/DA extend module with the PCF8591 single-chip, single-supply low-power 8-bit CMOS data acquisition device with four analog inputs, one analog output and a serial I2C-bus interface
Retired
No product available!
No product available!
5dB antenna for the Banana Pi R1 router in the version with 300Mps wifi and five LAN 100/1000 ports.
Retired
No product available!
STM32F103 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
CC3200 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
CC2530 and CC2540 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
It is a standard audio-video cable, which can be successfully used to connect Banana Pi M1 or Raspberry Pi 1 model B and A. Cable length is 98 cm, has two ends of the chinch type.
Retired
No product available!
COM-11964 Button a white economy grade 100mm diameter (outside diameter) dome illuminated push button comes with an LED, securing nut and a long life horizontal microswitch.
Retired
No product available!
Cobbler Plus - adapter enabling connection of GPIO Raspberry Pi A +, B + and Pi 2 lines to the contact plate (2.54 mm). The version is assembled. Adafruit 2029
Retired
No product available!
T-Cobbler Plus - adapter enabling connection of GPIO Raspberry Pi A +, B + and Pi 2 lines to the contact plate (2.54 mm). Goldpin connectors are included, for self-assembly. Adafruit 1989
Retired
No product available!
FPC tape length 250 mm, 50 lines, pitch 0.5 mm. Adafruit 1682
Retired
No product available!
μHex is the first low-power controller which is compatible with Arduino. It is very suitable for the battery power supply environment. A 210mAh CR2032 cell battery could make it work 60 days long. DFR0343
Retired
No product available!
The Leonardo ETH is a microcontroller board based on the ATmega32U4 and the new W5500 TCP/IP Embedded Ethernet Controller (datasheet).
Delivery date unknown
No product available!
Anna Kaziunas France