- Out-of-Stock
New products
New products
zł609.00
Delivery date unknown
zł462.10
24h
Available
Analog temperature sensor
ID: 557602
MOD-37.Z
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Analog temperature sensor TMP36GT9Z
Description
The built-in TMP36GT9Z sensor is used to measure the temperature in the range from - 40 ° C to + 125 ° C with a resolution of 0.5 ° C. The module has an analogue, voltage output, varying by 10 mV / ° C.
The module can be connected to the ADC converter input of any microcontroller and easy to read the temperature value. For example, at room temperature (+ 25 ° C), the output of the module will be a voltage of approx. 750 mV. A module with a sensor with a larger temperature range is also available.
Technical data:
- Code and name of the module: MOD-37.Z Analogue temperature sensor TMP36GT9Z
- Integrated circuit: TMP36GT9Z
- Description of pins: VCC, SIG, GND
- Power supply: from + 2.7V to 5.5V
- LED signaling: no, there is room for the LED diode
- Dimensions 21 mm x 11 mm
- RoHS: yes
Set contains:
- assembled MOD-37.Z Analog temperature sensor TMP36GT9Z
- set of connectors for self-assembly (3-pin 1 pcs)
To download
557602
Data sheet
- Interface
- Sygnał analogowy
- Type of sensor
- inny
- Power supply voltage
- 2.7..5.5V
- Sensor type
- Analogowy
You might also like
No product available!
Other products in the same category (16)
Comes with a 6"x6" (152mm x 152mm) square of Pyralux. It\'s ED-Y type copper at 35um (1 oz/ft2) and has a polymide of 25um (1 mil). The thick copper layer means it can carry a lot of current, and its trivial to solder to it. Adafruit 1894
Retired
No product available!
PCB and programmed circuit for the 230V switch controlled by any infrared remote control. AVT1840 A +
Retired
No product available!
The SparkFun ESP32 Thing Power Control Shield enables the ESP32 Thing to switch up to 5A of a DC load, providing a wide variety of options to control your next project! With a default voltage range of 5–28VDC, power can be connected to this shield in one of two ways. DEV-14155
Retired
No product available!
Tin LP with a diameter of 2mm on a spool, weight 100g. Stop Sn60Pb40
Retired
No product available!
No product available!
No product available!
No product available!
A circuit board for an android driver with FT311D. AVT5575 A
Retired
No product available!
MG2639 SparkFun Cellular Shield is a perfect addition to any Arduino project that requires connectivity when there’s no WiFi or Ethernet access nearby. The ZTE MG2639 module, which this shield is built around, supports SMS, TCP, UDP, and can even be used to make or receive phone calls. CEL-13120)
Retired
No product available!
No product available!
Ravi Doddannavar, Andries Barnard, Jayaraman Ganesh
Delivery date unknown
No product available!
Starter kit with the Raspberry Pi 3 model A + minicomputer, the kit also includes the official case for RPI 3 model A and a card with pre-installed NOOBS software and a 116-page guide.
Retired
No product available!
Basys 2 Spartan-3E FPGA Trainer Board (LIMITED TIME). 410-155-25
Retired
No product available!
Premium Jumper Wire 10-Pack F-F 6" Gray
Retired
No product available!
No product available!
Ennio Arimondo, Paul Berman, Chun Lin
Delivery date unknown
No product available!
MOD-37.Z