- Out-of-Stock
SparkFun Weather Shield
ID: 559794
Easy to use Arduino shield that grants you access to barometric pressure, relative humidity, luminosity, and temperature. There are also connections to optional sensors such as wind speed/direction, rain gauge, and GPS for location and super accurate timing. DEV-12081
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
The Weather Shield is an easy to use Arduino shield that grants you access to barometric pressure, relative humidity, luminosity and temperature. There are also connections on this shield to optional sensors such as wind speed, direction, rain gauge and GPS for location and super accurate timing.
These Weather Shields utilize the HTU21D humidity, MPL3115A2 barometric pressure, and ALS-PT19 light sensors and relies on the HTU21D and MPL3115A2 Arduino libraries. Each shield comes with two unpopulated RJ11 connector spaces (for optional hook up of rain and wind sensors) and a 6-pin GPS connector (for optional hook up of a GP635T GPS module). Finally, each Weather Shield can operate from 3.3V up to 16V and has built in voltage regulators and signal translators.
Attention! The Weather Shield comes as a stand-alone board. Headers, connectors, and additional sensors will need to be purchased separately, check the related items or wish list below!
This shield was designed for the SparkFun Redboard and Arduino Uno and will not work with other boards (like the Arduino Yun, for example) without modification.
This shield was designed for the SparkFun Redboard and Arduino Uno and will not work with other boards (like the Arduino Yun, for example) without modification.
Features
- Uses the HTU21D humidity sensor, MPL3115A2 barometric pressure sensor, and ALS-PT19 light sensor.
- Has connector for the GP-635T compact GPS module
- Has optional connectors for the SparkFun weather meters
- Weather shield can operate from 3V to 10V and has built in voltage regulators and signal translators
- Typical humidity accuracy of ±2%
- Typical pressure accuracy of ±50Pa
- Typical temperature accuracy of ±0.3C
Suggested reading:
- I2C Protocol
- Installing an Arduino library
- How to install Arduino shield headers
- What are pull-up resistors?
- HTU21D Humidity Sensor Hookup Guide
- MPL3115A2 Barometric Sensor Hookup Guide
559794
Other products in the same category (16)
CLIP CLC DECLARER WORKING WITH CENTR.DTMF - PLAINED AND PROGRAMMED UK? ADAPTER
Retired
No product available!
No product available!
The Microchip preparation enables intensive, concentrated blowing to inaccessible places, removes dust from various elements
Retired
No product available!
Differential Mini Amplified Surface Mount Silicon
Microphone with Enhanced RF Protectionr, 1,5 V to 5,5 V, Knowles Acoustics, RoHS
Retired
No product available!
The eMMC 5.1 flash memory module for Hardkernel Odroid C2 computers. Capacity 64GB, Android operating system installed. The set includes a microSD adapter. Hardkernel
Retired
No product available!
No product available!
Alphanumeric display OLED 16 characters x 2 lines, with built-in controller WS0010, communicating via 6800 interface, optionally 8080 or SPI. Winstar WEH001602AR
Retired
No product available!
No product available!
Pressure sensor module with I2C interface (BMP085), allows precise pressure measurement in the range of 300 to 1100 hPa with an accuracy of 1 hPa, RoHS
Retired
No product available!
Rectifier diode Schottky, THT, 40V, 1A, DO-41, LGE, RoHS
Retired
No product available!
Needle bending needle, for precise glue application, Flux 0.25mm internal diameter and 0,5144mm outside diameter
Retired
No product available!
Ultra wide angle lens with M12 mount included with the adapter. 2.8 mm focal length and 130° FoV. Designed to work with the Raspberry Pi HQ camera. ArduCAM LN032
Retired
No product available!
No product available!
No product available!
Introduction to Digital Design. Block Diagram / VHDL Examples; Richard E. Haskell & Darrin M. Hanna - EDU
Retired
No product available!
Camera module 0.3 Mpx with the Aptina Imaging MT9V111 CMOS sensor with a matrix resolution of 640 x 480 pixels and transmission speeds in the VGA format up to 30 FPS. Adapted to work in low light conditions. Communication via a parallel interface. ArduCAM B0059
Retired
No product available!
Easy to use Arduino shield that grants you access to barometric pressure, relative humidity, luminosity, and temperature. There are also connections to optional sensors such as wind speed/direction, rain gauge, and GPS for location and super accurate timing. DEV-12081