.png)
- Out-of-Stock
Arduino Music Shield VS1053B Audio Player and Recorder - Waveshare 11079
ID: 560667
Music Shield for Arduino Development, Audio Play/Record, VS1053B Onboard
Overview
Music Shield is an Arduino expansion board for playing/recording audio, features onboard audio codec chip VS1053B and a TF card slot, supports common used audio formats.
Features
- Arduino standard interfaces, compatible with Arduino boards like Arduino UNO, Leonardo, NUCLEO, XNUCLEO
- Supported formats : MP3/AAC/WMA/WAV/MIDI, etc.
- Onboard TF card slot, audio files in TF card can be played directly
- Onboard MIC for recording, with standard 3.5mm 4-segment headphone jack
- Onboard voltage level converter 74VHC125, compatible with 3.3V/5V MCUs
- One-key control, play music and adjust volume easily by the navigation key
- Features I2S and MIDI interface for functional expansion
Note : Limited by the transmission speed and memory shortage, Arduino boards like UNO and Leonardo can neither play WAV files, nor use the recording function. NUCLEO or Due are recommended.
Development Resources
Wiki : www.waveshare.com/wiki/Music_Shield
-
Weight: 0.015 kg
- Music Shield x 1
560667
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
You might also like
Gravity: Voice Recorder Module is a sound recording module powered by 5V voltage. It can store sounds up to 10 seconds long. DFRobot SEN0197
zł26.24
Delivery date unknown
No product available!
This Bluetooth Audio receiver module includes a USB port and TF card slot. With a pre-amp output, you can drive headphones or a 3W speaker directly. You can also add an active power amplifier and connect a loudspeaker. The module supports MP3, WMA, WAV and lossless FLAC audio formats. DFRobot TEL0108
zł71.00
Delivery date unknown
No product available!
Other products in the same category (16)
Video splitter for connecting one input device to 8 receivers. Maximum 4K resolution supported. Lanberg SPV-HDMI-0008
Retired
No product available!
Video switch that allows you to connect 5 input devices to one HDMI receiver. The input signal can be selected using a button on the casing or the included remote control. Lanberg SWV-HDMI-0005
Retired
No product available!
A set of 8 knives, including 4 knives with broken blades and 4 special-purpose knives. Vorel 76280
Retired
No product available!
Module with an analog temperature and humidity sensor based on the SHT10 system. It is characterized by high reliability and stability with low energy consumption. It is compatible with 3.3V and 5V controllers. DFRobot DFR0066
Retired
No product available!
Module with a CCS811 air quality sensor for measuring the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via the I2C interface (Gravity connector). DFRobot SEN0318
Retired
No product available!
Module with a gesture and touch sensor. It recognizes 7 types of gestures and has 5 touch buttons. It is supplied with a voltage ranging from 3.3 V to 5 V and communicates via UART. DFRobot SEN0285
Retired
No product available!
Module with a 3-axis analog MMA7361 accelerometer. There are 3 Gravity connectors on the board (for each axis). The operating range of the sensor can be configured using a DIP switch. DFRobot DFR0143
Retired
No product available!
Module with a UV ultraviolet light sensor VEML6075. Enables measurement of the level of UVA (350-375 nm) and UVB (315-340 nm) radiation. It communicates via the I2C bus. DFRobot SEN0303
Retired
No product available!
The I2C-GPIO converter module is powered with the voltage of 5 V. It allows you to extend the number of digital pins of the Arduino-compatible board with an additional 16 IO pins. DFRobot DFR0013
Retired
No product available!
KAmodRPI RS485 CAN HAT is a shield for the Raspberry Pi computer that extends its interfaces with RS485 and CAN. Bus signals are led out to goldpin connectors and terminal blocks.
Retired
No product available!
Opening/closing sensor designed for mounting on windows and doors. It is equipped with an RF wireless communication module operating at 433 MHz. Sonoff DW2 - RF
Retired
No product available!
Opening/closing sensor designed for mounting on windows and doors. It is equipped with a WiFi wireless communication module. Sonoff DW2
Retired
No product available!
Universal WiFi controlled switch. It can control one home appliance. Sonoff Basic R2 v2.2
Retired
No product available!
Wireless temperature and humidity sensor. It allows you to track changes in temperature and humidity in your home. Shelly H&T
Retired
No product available!
Power adapter with a microUSB socket designed for the Shelly H&T sensor. It allows you to replace the battery power of the sensor with a constant 5V power supply. Shelly H&T Usb Adapter
Retired
No product available!
Device for activating scenes and actions with WiFi communication. It can handle 3 connected input devices and show their status and control other connected Shelly relays, sensors or devices controlled by HTTP, MQTT or CoAP. Shelly i3
Retired
No product available!
Music Shield for Arduino Development, Audio Play/Record, VS1053B Onboard