- Out-of-Stock
ODROID C0 with Amlogic S805
ID: 561187
Computer for those who wish to make a more flexible and portable applications. It is a minimized hardware version of the ODROID-C1+. Battery power circuit is fully integrated. Just attach a 3.7V Li+ battery and make it mobile. It is highly suitable for IoT projects, wearables, and other applications that require a lightweight device.
Description
The ODROID-C0 is a computer for those who wish to make a more flexible and portable applications. It is a minimized hardware version of the ODROID-C1+. Battery power circuit is fully integrated. Just attach a 3.7V Li+ battery and make it mobile. It is highly suitable for IoT projects, wearables, and other applications that require a lightweight device.
All the ODROID-C1/C1+ OS images are fully compatible with the ODROID-C0. Some of the modern operating systems that run on the ODROID-C0 are Ubuntu, Android, Arch Linux, Debian, and OpenELEC, with thousands of free open-source software packages available. There are also plenty of custom OS available for using the ODROID-C0 as a multimedia center, Kodi, gaming station, headless server and much more at our ODROID community.
The key features and improvements over the original ODROID-C1+
- Amlogic ARM® Cortex®-A5(ARMv7) 1.5Ghz quad core CPUs
- Mali™-450 MP2 GPU (OpenGL ES 2.0/1.1 enabled for Linux and Android)
- 1Gbyte DDR3 SDRAM
- eMMC4.5 HS200 Flash Storage slot / UHS-1 SDR50 MicroSD Card slot
- 40pin + 7pin GPIOs (unpopulated)
- USB 2.0 Host x 2 (unpopulated)
- Infrared(IR) Receiver (unpopulated)
- Li+ rechargeable battery charger for wearable and robots application
- Battery voltage level is accessible via ADC in the SoC.
- DC/DC step-down converters for higher power efficiency
- DC/DC step-up converter for 5Volt rails (USB host and HDMI) from a Li-Polymer battery
- DIY friendly C0 Connector Pack is available for handy prototyping
* An additional MicroSD card or an eMMC module is required to install the OS. We recommend the eMMC module as it has much higher performance than standard MicroSD cards.
* The ODROID-C0 is a low cost and light weight variant to the original ODROID-C1+ model. The PCB size is reduced about 24% and the weight is reduced to 16g from 40g.
The ODROID-C0 is a low cost and light weight variant to the original ODROID-C1+ model. The PCB size is reduced about 24% and the weight is reduced to 16g from 40g.
- Adding a Li-polymer battery management IC.
- Remove the Gbit Ethernet connectivity.
- Reduce the number of USB host ports to two from four.
- Remove the USB-OTG port.
- Unpopulated a few connectors for various DIY projects.
Features
- Processor: Amlogic S805 SoC ARM® Cortex®-A5 (ARMv7) 1.5GHz Quad Core ARMv7 architecture @28nm wafer
- Memory: 1Gbyte DDR3 RAM 792Mhz
- 3D Accelerator: ARM® Mali™-450 MP2 OpenGL ES 2.0 / 1.1
- Flash Storage: eMMC Module Socket: eMMC module (option)
MicroSD Card Slot: 8~128GB MicroSD UHS-1 (option) - USB2.0 Host: High speed standard A type connector x 2 ports
- Video Output: HDMI
- Audio Output: HDMI, I2S
- Real Time Clock: On-board RTC function with a coin-shaped backup battery connector
- IO Expansion: 40pin port (GPIO/UART/SPI/I2C/ADC)
7pin port (I2S) - WiFi: USB IEEE 802.11b/g/n 1T1R WLAN with Antenna (USB module) (option)
- Power: 5V 2A Power (option)
3.7V Li+ battery power - System Software: Ubuntu 14.04 + OpenGL ES on Kernel 3.10 LTS
Android 4.4.x on Kernel 3.10 LTS
Full source code is accessible via our Github. - PCB Size: 58 x 56 x 11 mm approx. (Weight: 16 gram w/o heat sink, 30 gram with an optional heat sink)
- PCB Thickness: 1.0mm
561187
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Available
Other products in the same category (16)
No product available!
The module with the ACS725 current sensor with a direct current measuring range up to 10 A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020616
Retired
No product available!
Printed circuit board for vapor extraction controller. AVT3215 A
Retired
No product available!
No product available!
No product available!
Module with a UV ultraviolet light sensor VEML6075. It enables measurement of the level of UVA (350-375 nm) and UVB (315-340 nm) radiation. It communicates via the I2C bus. Pimoroni PIM460
Retired
No product available!
The Compute Module 3 Development Kit is for designers who like the Raspberry Pi 3 functionality but need a smaller form factor for their embedded designs. RPI-COMPUTE3-KIT
Retired
No product available!
Unlimited C compiler and assembler toolset for 8051 core-based microcontrollers with USB Dongle-based license
Retired
No product available!
Robert Bruce Thompson, Barbara Fritchman Thompson
Delivery date unknown
No product available!
No product available!
Male terminal block, angled, 2-pin. Pitch 5.0mm. Height 7.8mm. 2EDGRC-5.0-2P
Retired
No product available!
Luis Moura, Izzat Darwazeh
Delivery date unknown
No product available!
Camera with OV2710 CMOS sensor with a resolution of 1945x1109 px. It communicates via a parallel interface. ArduCAM U6034
Retired
No product available!
CM Dafermos, Eduard Feireisl
Delivery date unknown
No product available!
Fully integrated microstepping motor controller with motion engine and SPI, HTSSOP38, STM, RoHS
Retired
No product available!
Power adapter with a microUSB socket designed for the Shelly H&T sensor. It allows you to replace the battery power of the sensor with a constant 5V power supply. Shelly H&T Usb Adapter
Retired
No product available!
Computer for those who wish to make a more flexible and portable applications. It is a minimized hardware version of the ODROID-C1+. Battery power circuit is fully integrated. Just attach a 3.7V Li+ battery and make it mobile. It is highly suitable for IoT projects, wearables, and other applications that require a lightweight device.