- Out-of-Stock
New products
New products New products
zł343.01
24h
Available
Available
Available
Available
Available
eMMC Module C2 Linux Black - 8GB
ID: 561312
Pre-installed Ubuntu 16.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung. JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode. The eMMC chipset is only compatible with Amlogic S905 and S805 series(ODROID-C1+ / C0 / C2)
Description
Pre-installed Ubuntu 16.04 or latest version.
Ready to run out of the box
eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode.
The eMMC chipset is only compatible with Amlogic S905 and S805 series(ODROID-C1+ / C0 / C2)
This eMMC chipset is not compatible with ODROID-XU4 / XU3 / U3 / U2 / X series
eMMC Module Reader is included
Adapter micro-SD for eMMC
Moduł eMMC attached to adapter
Storage I/O comparison
The C2 can boot from a MicroSD card or an eMMC module. The MicroSD interface supports the higher performance UHS-1 mode as well. File access of a 512MB file (read/write) on two different storage options shows distinct performance differences. The eMMC 5.0 storage is ~7x faster than the MicroSD Class-10 card in read tests. The MicroSD UHS-1 card is ~2x faster than the MicroSD Class-10 card in read tests. The MicroSD UHS-1 card provides a great low-cost option for many applications!
To obtain the results in the storage I/O comparison graph, type the following lines at a command prompt.
Write speed command :
$ dd if=/dev/zero of=test.tmp oflag=direct bs=8M count=64
Read speed command :
$ dd if=test.tmp of=/dev/null iflag=direct bs=8M count=64
561312
Data sheet
- Compatible with
- Odroid C2
- Card capacity
- 8GB
- Operating system
- LINUX
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
150W lead and lead free soldering pot. It serves, among others for tinning/soldering of cable ends.
Retired
No product available!
Set of 6 insulating tapes in the following colors: red, yellow, yellow-green, green, blue and black.
Retired
No product available!
Vision Edge computing platform with ARM Cortex-A53 1.2 GHz 64-bit quad-core processor, ARM Cortex-R5 600 MHz dual-core processor, embedded Mali400 graphics processor and FPGA chip. MYIR VECP Starter Kit
Retired
No product available!
The minicomputer with the Intel Celeron J4115 quad-core processor (2.5 GHz, 64-bit) has 2 slots for DDR4 RAM modules. Additionally, it is equipped with, among others: Gigabit Ethernet, HDMI 2.0 port and Display Port 1.2 4K/60Hz, four USB sockets, 24 GPIO, PCI-e slot, two SATA3 connectors. Rev-B+. ODROID H2+
Retired
No product available!
LPCXpresso55S16 evaluation kit with LPC55S16 microcontroller with ARM Cortex-M33 core. The board contains built-in LPC-Link2, audio subsystem, accelerometer, USB interfaces and Arduino connectors. NXP LPC55S16-EVK
Retired
No product available!
The MIMXRT1062DVL6A Processor Evaluation Kit, which runs up to 600 MHz, has 256 MB of SDRAM, 512 MB of Flash and 64 QSPI Flash. NXP MIMXRT1060-EVK
Retired
No product available!
Starter kit with the Kinetis K32 L2B microcontroller, integrated with the OpenSDA programmer-debugger, LCD display, accelerometer and MEMS magnetometer and USB connector. Conclusions compatible with Arduino. NXP FRDM-K32L2B3
Retired
No product available!
Wired mouse with a precise optical sensor. It has a button to change the resolution in four levels: 800/1200/1600/2400 DPI. 1.8m cable with USB plug. Natec NMY-0667
Retired
No product available!
Kit with LS1046A Freeway development board equipped with 4-core LS1046A processor, 4 GB RAM, 4GB Flash, 4 Gigabit Ethernet connectors, 2 USB 3.0 connectors, microSD slot and two M.2 slots. NXP FRWY-LS1046A-AC
Retired
No product available!
Adapter for connecting a Raspberry Pi to the OM-SE050ARD development board. It allows you to run the EdgeLock SE050 application on a Raspberry Pi. NXP OM-SE050RPI
Retired
No product available!
LPC55S69JEV98K, ARM Cortex-M33 Microcontroller, 32 bit, 150 MHz, 640 KB Flash, VFBGA98
Retired
No product available!
USB - CAN converter module. It allows the device to be connected to a computer (USB) or microcontroller (UART) via the CAN bus. USB CAN CONVERTER (UCCB)
Retired
No product available!
Set with HQ camera, HDMI adapter, lens, tripod and Jetvariety adapter. Kit designed for NVIDIA Jetson Nano. ArduCAM B0243
Retired
No product available!
A minisumo robot on a tracked chassis with Pololu 100:1 HP motors. Fully assembled robot, additionally requires four AA batteries. Pololu 3127
Retired
No product available!
A module that allows you to connect ArduCAM cameras with a CSI interface to a PC or minicomputers via the USB3.0 interface. It not only supports high-resolution, high-frame rate image sensors, but also a stereoscopic camera and IRCUT control functions. ArduCAM B0111
Retired
No product available!
A small minicomputer with a RockChip RK3328 quad-core SoC chip (ARM Cortex-A53). The computer is equipped with 2 GB DDR4 RAM, Gigabit Ethernet port and USB 3.0. Each module has its own unique MAC address. NanoPi NEO3 2GB
Retired
No product available!
Pre-installed Ubuntu 16.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung. JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode. The eMMC chipset is only compatible with Amlogic S905 and S805 series(ODROID-C1+ / C0 / C2)