- Out-of-Stock
This in-system programmer can be used to program AVR microcontrollers and AVR-based controller boards, such as our Orangutan robot controllers and the 3pi robot. The programmer emulates an STK500 on a virtual serial port, making it compatible with standard AVR programming software, and it supports devices running at either 3.3 V or 5 V. The programmer also features a TTL-level serial port, enabling general-purpose serial communication for debugging or programming microcontrollers with a serial bootloader. An ISP cable and a 1×6 double-sided male header are included with the fully-assembled programmer.
The Pololu USB AVR Programmer v2 is a compact, low-cost in-system programmer (ISP) for Atmel’s AVR microcontrollers. The programmer provides an interface for transferring a compiled AVR program from your computer to the target AVR’s non-volatile memory, allowing it to run the program. It is a good solution for programming AVR-based controllers like our Orangutan robot controllers, and it can also be used to update, replace, or remove the bootloader on Arduino boards and our Arduino-compatible A-Star 32U4 controllers. This programmer is designed to work well with both 3.3 V and 5 V devices, and it can even be configured to provide power to the target device in low-power systems.
The programmer connects to your computer’s USB port via a standard USB A to Micro-B cable (not included) and communicates with your programming software, such as Atmel Studio, AVRDUDE, or Arduino, through a virtual COM port using the STK500 protocol. The programmer connects to your target device via an included 6-pin ISP programming cable (the older, 10-pin ISP connections are not directly supported, but it’s easy to create or purchase a 6-pin-to-10-pin ISP adapter). The programmer also acts as a USB-to-TTL serial adapter, providing a TTL-level serial port that can be used to communicate with other serial devices from your computer. It ships fully assembled with connectors soldered in as shown.
Supported AVR microcontrollers
The programmer should work with all AVRs that can be programmed with the AVR ISP (in-system programming) interface, which is also known as in-circuit serial programming (ICSP), serial programming, or serial downloading, but it has not been tested with all devices. We expect it to work with most AVRs in the megaAVR (ATmega) family, and it works with some members of the tinyAVR (ATtiny) family, but it does not support the Tiny Programming Interface (TPI), and it does not work with the XMEGA family or with 32-bit AVRs. The programmer features upgradable firmware, allowing updates for future devices.
The programmer is designed for use with AVR microcontrollers running at either 3.3 V or 5 V. By default, the programmer expects the target to be self-powered, but it can be configured to deliver power to the target device in low-power systems.
Supported operating systems
We support using the Pololu USB AVR Programmer v2 and its configuration software on desktop versions of Windows (Vista, 7, 8, and 10), Linux, and Mac OS X 10.11 or later. Older versions of Windows are not supported.
Bonus feature: TTL-level serial port
This programmer doubles as a USB-to-serial adapter. The programmer installs as two virtual COM ports: one for communicating with programming software and one for general-purpose serial communications. This means that you can seamlessly switch between programming an AVR and debugging it through the TTL serial port without having to open and close your terminal program. In addition to the serial transmit (TX) and receive (RX) lines, the programmer lets you use A and B as serial handshaking lines that can be configured using our software.
The six pins on the serial header (GND, A, VCC, TX, RX, and B) are arranged to be similar to the pinout of commonly-available FTDI USB-to-serial cables and breakout boards. In the default configuration, pin B is used as the DTR output (and pin A is an unused input), which allows you to plug the programmer directly into a variety of Arduino-compatible boards and use it to upload programs to the board via a serial bootloader.
Included accessories
The Pololu USB AVR Programmer v2 ships fully assembled with ISP and serial connectors soldered in, and it includes the accessories shown in the picture below. The 6-pin ISP cable can be used to program AVRs. The 1×6 double-sided male header can be plugged into the serial header to effectively reverse its gender (making it possible to connect that header to a breadboard or female jumper wires).
Comparison to the older Pololu USB AVR Programmer
The Pololu USB AVR Programmer v2 is an updated version of our Pololu USB AVR Programmer (product #1300). It features a number of improvements compared to the original:
This programmer does not include a USB cable, and it does not have the SLO-scope bonus feature. In addition to these changes, many other details are different between the v2 programmer and the original; please be sure to refer to the user’s guide for the USB AVR Programmer v2 to familiarize yourself with this programmer. This programmer was released in March 2016, so any written references to the “Pololu USB AVR Programmer” from before that time refer to the original (older) programmer.
Manufacturer
Responsible person
Pololu 972 is a 30 cm IDC6 F/F cable for connecting ISP programmers and devices with 2×3 2.54 mm pitch connectors. It is suitable for working with microcontrollers and embedded systems, providing a durable and reliable connection.
USBasp programmer for ATMEL AVR microcontrollers, is equipped with ISP IDC10 connector, the kit includes a 20cm connecting cable. The programmer has the option of powering the supplied PCB and selecting the output voltage
No product available!
Raspberry computer case: Pi 3 model B +, Pi 3 model B, Pi 2 model B and Pi 1 model B + in blue. Made of plastic
No product available!
Raspberry computer case: Pi 3 model B +, Pi 3 model B, Pi 2 model B and Pi 1 model B + in black. Made of plastic
No product available!
Mike Westerfield
No product available!
Raspberry Pi RPI COMPUTE MODULE module
No product available!
Bluetooth 2.1 + EDR module based on RN41. It communicates via the UART interface. SparkFun WRL-12580
No product available!
No product available!
No product available!
No product available!
KEMOT double-sided tape with a width of 10 mm and a length of 6 m is a foam adhesive tape that effectively replaces traditional fastening methods such as rivets, screws, or liquid adhesives. Its design eliminates the need for drilling and screwing, making it easier to mount various elements without damaging surfaces.
No product available!
Universal solder extractor made of plastic, to remove excess tin. NAR0049
No product available!
Vaseline oil from AG Termopasty is a lubricant for machine parts and precision mechanisms. Its task is to reduce friction and maintain elements exposed to weather conditions. AG Termopasty ART.AGT-017
No product available!
Quick coupler UY*2 4CI-2007A quick-connect fitting that allows two wires to be connected with a diameter of 0.35 to 0.9 mm. They are used for quick and precise connection of telephone wires or twisted-pair cables (UTP, FTP). UY*2 4CI-2007
No product available!
Soldering tape used to collect excess tin with a gray 1.5 mm, 1.5 m long
No product available!
A liquid for cleaning printed circuit boards based on isopropyl alcohol, perfectly removes binder residues, as well as lubricants and oils
No product available!
No product available!
This in-system programmer can be used to program AVR microcontrollers and AVR-based controller boards, such as our Orangutan robot controllers and the 3pi robot. Pololu 3170