- Out-of-Stock
Teensy LC
ID: 563088
PJRC TEENSYLC
Description
The Teensy is a breadboard-friendly development board with loads of features in a, well, teensy package. The Teensy LC (Low Cost) is a 32 bit microcontroller board that provides you with an uncomplicated option for getting started with the Teensy line of products without breaking the bank!
The Teensy LC comes pre-flashed with a bootloader so you can program it using the on-board USB connection: No external programmer needed! You can program for the Teensy in your favorite program editor using C or you can install the Teensyduino add-on for the Arduino IDE and write Arduino sketches for Teensy!
The processor on the Teensy also has access to the USB and can emulate any kind of USB device you need it to be, making it great for USB-MIDI and other HID projects. The 32 bit processor brings a few other features to the table as well, such as multiple channels of Direct Memory Access and an I2S digital audio interface! There are also 2 separate interval timers! Also, the Teensy LC can provide system voltage of 3.3V or 5V to other devices at up to 5-20mA.
All of this functionality is jammed into a 1.4 x 0.7 inch board with all headers on a 0.1" grid so you can slap it on a breadboard and get to work! So, what sets the Teensy LC apart from the Teensy 3.1? First off, this version has been streamlined to be as cost effective as possible. Obviously, the LC doesn’t share a lot of power that the 3.1 possesses but by no means does it make the LC a ‘weak’ board! The Teensy LC is equipped with 8kB RAM, 62kB of flash memory, and 27 Digital I/O pins with 13 high res Analog inputs.
Note: The Teensy LC does not come with a micro-B USB cable, please check the Recommended Products section below for an appropriate one.
Dimensions
1.4 x 0.7" (~35 x 18 mm)
Features
- 32 bit ARM Cortex-M0+ 48 MHz CPU
- 62kB Flash Memory, 8kB RAM, 1/8(emu)kB EEPROM
- 13 High Resolution Analog Inputs
- 27 Digital I/O Pins (NOT 5V Tolerant)
- 10 PWM outputs
- 7 Timers for intervals/delays, separate from PWM
- 3 UARTs (serial ports)
- SPI, I2C, & I2S
- I2S (for high quality audio interface)
- 4 Lightweight DMA channels
- Touch Sensor Inputs
563088
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Adapter for Xbee (ZigBee) radio modules compatible with Teensy 3.1. On the board, the pins of both modules are led out to connectors with a 2.54 mm pitch. SparkFun BOB-13311
zł40.36
Delivery date unknown
No product available!
A small module, matching the breadboard, containing a 32-bit microcontroller with ARM Cortex M7 core. PJRC TEENSY40
zł124.07
24h
Available quantity: 24
Available
Other products in the same category (16)
Camera with CMOS MT9M112 sensor with a resolution of 1280x1024 pixels. It communicates via the DVP parallel interface. ArduCAM U6080
Retired
No product available!
Adapter dedicated to Omnivision cameras. Allows you to connect an image sensor to the evaluation kit. ArduCAM B0012
Retired
No product available!
Camera module 18 Mpx with AR1820HS sensor working with Raspberry Pi. It offers a video resolution of up to 4912x3684 pixels at 15 fps. ArduCAM B0164
Retired
No product available!
Camera module based on the OV13850 CMOS matrix with a resolution of 4224x3136 px (13 MPx). Designed for use with ArduCAM USB Shield. ArduCAM B0129
Retired
No product available!
ArduCAM OV9281 1MP Global Shutter USB Camera Evaluation Kit - Evaluation Kit with 1MP OV9281 166°...
A set with a camera with a resolution of 1 MPx with an OV9281 sensor, a USB 3.0 adapter and a cable. ArduCAM EK024
Retired
No product available!
Module with USB 2.0 interface dedicated to ArduCAM cameras. Supports sensors with MIPI interface. Has a built-in 16 MB hardware frame buffer. ArduCAM B0175
Retired
No product available!
Micro analog servo with plastic gear. It has a range of motion of 90°. GH-S37A
Retired
No product available!
GSM/GPRS + GPS module based on the RDA8955 chip. It integrates protocol stacks such as GSM/GPRS and supports the basic functions of voice calls, SMS and GPS data transmission. DFRobot TEL0134
Retired
No product available!
Aluminum case for minicomputer Raspberry Pi 4 model B, black color
Retired
No product available!
HAT module with RTC DS3231SN clock and MAX705 reset system designed for Raspberry Pi and Jetson Nano. The board has a CR1220 battery socket and a C-type USB connector. Waveshare RTC WatchDog HAT
Retired
No product available!
The expansion module is designed to work with a portable computer built into the Raspberry Pi 400 keyboard. The board has two 40-pin connectors placed in a vertical position and a connector for RPI 400 at an angle of 45 °. Waveshare PI400-GPIO-ADAPTER-C
Retired
No product available!
The power supply module with the RTC DS3231SN clock is designed for the Raspberry Pi. It allows you to power minicomputer with voltage up to 28 V and create scripts for the power-on sequence. Pimoroni WITTY_PI_3_R2
Retired
No product available!
Module of the 8-channel I2C expander based on the TCA9548A system. It enables communication with many I2C devices that have the same address. Pimoroni 8086-006
Retired
No product available!
Mini board with RP2040 microcontroller equipped with two ARM Cortex-M0+ 133 MHz cores, 264 kB RAM. The board also has 8 MB of QSPI flash memory. The circuit can be programmed in C/C++, CircuitPython or MicroPython. PIM577
Retired
No product available!
Module with a black and white e-Paper display with a diagonal of 2.13" and a resolution of 250x122 px. SPI interface. Pimoroni PIM368
Retired
No product available!
Metal case with fan for Raspberry Pi 4 model B in black
Retired
No product available!
PJRC TEENSYLC