- Out-of-Stock
Automatic switch with PIR 230V motion sensor
ID: 565008
The device for automatic control of lighting or other electrical devices. Installed in place of an ordinary wall switch. He reacts to movement
Description
The device for automatic control of lighting or other electrical devices. Installed in place of an ordinary wall switch. The sensor switches the device on automatically after the movement has been registered, the switch-off takes place with a delay which can be adjusted.
properties
- Operating voltage: 180-240 V (50/60 Hz)
- Maximum working current: ≤ 0.5 A
- Maximum load: up to 100 W
- Angle of action: 140 °
- Detection range: up to 8 m
- Switch-off time: adjustable, min. 10 s, max. 60 sec
- Installation height: approx. 1.5 m above the ground
- The lighting intensity can be adjusted: day / night
- Permissible ambient temperature: -20 ~ 50 ° C
- Dimensions: 86 x 86 x 30 mm
565008
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
A small module with a PIR motion sensor. It allows detecting movement within a maximum range of 6 meters (default up to 3 meters). The measuring angle is 120 degrees. The module has a connector in accordance with the Grove standard. Seeed Studio 101020020
zł42.83
24h
Available quantity: 2
Available
PIR motion sensor module for Arduino and Raspberry Pi. DFRobot SEN0018
zł19.46
24h
Available quantity: 6
Available
Other products in the same category (16)
Module with a 3-axis gyroscope (ITG 3200 system). The measuring range is ± 2000 ° / s. The I2C interface is used for communication. The module has a low power consumption (typically 6.5 mA). The module has a connector in accordance with the Grove standard. Seeed studio 101020050
Retired
No product available!
Module module with ADC121C021 12-bit converter. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 103020013
Retired
No product available!
No product available!
No product available!
No product available!
No product available!
Twisted housing, dedicated to the Orange Pi Zero computer. The housing protects the computer against dust, accidental short circuits and mechanical damage. Properly prepared holes allow you to use all the sockets that Orange Pi Zero has been equipped with.
Retired
No product available!
No product available!
Banana Pi M2+ is another ARM SoC powered development board that offers great computing performance in an ultra portable form factor. It is a 65mm square with Allwinner H3 Quad-core A7 SoC and 1GB DDR3 RAM
Retired
No product available!
Banana Pi camera module for Banana Pi M3, includes CMOS sensor module: OV5640 (5M Pixel)
Retired
No product available!
Printed circuit board and programmed AA / AAA cell capacity tester. AVT3169 A +
Retired
No product available!
AVT kit for self-assembly of tester capacity AA / AAA cells. AVT3169 B
Retired
No product available!
Assembled cell capacitor AA / AAA. AVT3169 B
Retired
No product available!
Printed circuit board for water level indicator. AVT1949 A
Retired
No product available!
AVT kit for self-assembly of the water level indicator. AVT1949 B
Retired
No product available!
No product available!
The device for automatic control of lighting or other electrical devices. Installed in place of an ordinary wall switch. He reacts to movement